ASTM D 4307 : 1999 : R2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Preparation of Liquid Blends for Use as Analytical Standards
Hardcopy , PDF
11-11-2014
English
01-05-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Standard Practice
|
| Pages |
3
|
| ProductNote |
Reconfirmed 2010
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This practice covers a laboratory procedure for the preparation of small volumes of multicomponent liquid blends for use as analytical standards.
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.
1.3 This practice is limited to those components that fulfill the following conditions:
1.3.1 They are completely soluble in the final blend.
1.3.2 They are not reactive with other blend components or with blend containers.
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.
1.3.3.1 The butane content of the blend is not to exceed 10 %. (Warning: Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.) Components with a vapor pressure higher than butanes are not to be blended.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7260 : 2019 | Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 5623 : 2019 | Standard Test Method for Sulfur Compounds in Light Petroleum Liquids by Gas Chromatography and Sulfur Selective Detection |
| ASTM D 5501 : 2012 : R2016 | Standard Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas Chromatography |
| ASTM D 7059 : 2009 : R2017 | Standard Test Method for Determination of Methanol in Crude Oils by Multidimensional Gas Chromatography |
| ASTM D 7807 : 2012 | Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection |
| ASTM D 7578 : 2018 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 7740 : 2011 : R2016 | Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants |
| ASTM D 7096 : 2019 | Standard Test Method for Determination of the Boiling Range Distribution of Gasoline by Wide-Bore Capillary Gas Chromatography |
| ASTM D 7796 : 2017 | Standard Test Method for Analysis of Ethyl tert-Butyl Ether (ETBE) by Gas Chromatography |
| ASTM D 5986 : 1996 : R2015 | Standard Test Method for Determination of Oxygenates, Benzene, Toluene, C<inf>8</inf >–C<inf> 12</inf> Aromatics and Total Aromatics in Finished Gasoline by Gas Chromatography/Fourier Transform Infrared Spectroscopy |
| ASTM D 5135 : 2016 : EDT 1 | Standard Test Method for Analysis of Styrene by Capillary Gas Chromatography |
| ASTM D 5442 : 2017 | Standard Test Method for Analysis of Petroleum Waxes by Gas Chromatography |
| ASTM D 7920 : 2015 : EDT 1 | Standard Test Method for Determination of Fuel Methanol (M99) and Methanol Fuel Blends (M10 to M99) by Gas Chromatography |
| ASTM D 6730 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
| ASTM D 4815 : 2015 : REV B | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
| ASTM D 5580 : 2015 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <emph type="ital"> p/m</emph>-Xylene, <emph type="ital">o</emph>-Xylene, C<inf>9</inf> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
| ASTM D 7806 : 2012 | Standard Test Method for Determination of the Fatty Acid Methyl Ester (FAME) Content of a Blend of Biodiesel and Petroleum-Based Diesel Fuel Oil Using Mid-Infrared Spectroscopy |
| ASTM D 6584 : 2017 | Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography |
| ASTM D 7266 : 2013 : R2018 : EDT 1 | Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (External Standard) |
| ASTM D 7151 : 2015 | Standard Test Method for Determination of Elements in Insulating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 7875 : 2014 | Standard Test Method for Determination of Butanol and Acetone Content of Butanol for Blending with Gasoline by Gas Chromatography |
| ASTM D 4626 : 1995 : R2015 | Standard Practice for Calculation of Gas Chromatographic Response Factors |
| ASTM D 6142 : 2016 | Standard Test Method for Analysis of Phenol by Capillary Gas Chromatography |
| ASTM D 6144 : 2017 | Standard Test Method for Analysis of AMS (α-Methylstyrene) by Capillary Gas Chromatography |
| ASTM D 5769 : 2015 | Standard Test Method for Determination of Benzene, Toluene, and Total Aromatics in Finished Gasolines by Gas Chromatography/Mass Spectrometry |
| ASTM D 5845 : 2001 : R2016 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <emph type="ital">tert</emph>-Butanol in Gasoline by Infrared Spectroscopy |
| ASTM D 8071 : 2017 | Standard Test Method for Determination of Hydrocarbon Group Types and Select Hydrocarbon and Oxygenate Compounds in Automotive Spark-Ignition Engine Fuel Using Gas Chromatography with Vacuum Ultraviolet Absorption Spectroscopy Detection (GC-VUV) |
| ASTM D 7360 : 2016 | Standard Test Method for Analysis of Benzene by Gas Chromatography with External Calibration (Withdrawn 2023) |
| ASTM D 6443 : 2014 : R2019 : EDT 1 | Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure) |
| ASTM D 5060 : 2012 | Standard Test Method for Determining Impurities in High-Purity Ethylbenzene by Gas Chromatography |
| ASTM D 4951 : 2014 | Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM D 4735 : 2019 | Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography |
| ASTM D 7057 : 2018 | Standard Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography (External Standard) |
| ASTM D 7371 : 2014 | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method) |
| ASTM D 5917 : 2015 : R2019 | Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and External Calibration |
| ASTM D 7845 : 2017 | Standard Test Method for Determination of Chemical Species in Marine Fuel Oil by Multidimensional Gas Chromatography/Mass Spectrometry |
| ASTM D 7040 : 2004 : R2015 | Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM D 8267 : 2019 | Standard Test Method for Determination of Saturated Hydrocarbon, Aromatic, and Diaromatic Content of Aviation Turbine Fuels Using Gas Chromatography with Vacuum Ultraviolet Absorption Spectroscopy Detection (GC-VUV) |
| ASTM D 7974 : 2015 | Standard Test Method for Determination of Farnesane, Saturated Hydrocarbons, and Hexahydrofarnesol Content of Synthesized Iso-Paraffins (SIP) Fuel for Blending with Jet Fuel by Gas Chromatography |
| ASTM D 7576 : 2016 | Standard Test Method for Determination of Benzene and Total Aromatics in Denatured Fuel Ethanol by Gas Chromatography (Withdrawn 2022) |
| ASTM D 7754 : 2016 | Standard Test Method for Determination of Trace Oxygenates in Automotive Spark-Ignition Engine Fuel by Multidimensional Gas Chromatography |
| ASTM D 7861 : 2014 : R2019 | Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy |
| ASTM D 5441 : 1998 : R2017 | Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.