ASTM D 4007 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)
Hardcopy , PDF
11-11-2014
English
01-06-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.02, 2017 Defines the laboratory determination of water and sediment in crude oils by means of the centrifuge procedure.
| Committee |
D 02
|
| DevelopmentNote |
Also numbered as API MPM CH10.3. (08/2013)
|
| DocumentType |
Test Method
|
| Pages |
13
|
| ProductNote |
Reconfirmed 2011
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method describes the laboratory determination of water and sediment in crude oils by means of the centrifuge procedure. This centrifuge method for determining water and sediment in crude oils is not entirely satisfactory. The amount of water detected is almost always lower than the actual water content. When a highly accurate value is required, the revised procedures for water by distillation, Test Method D4006 (API MPMS Chapter 10.2) (Note 1), and sediment by extraction, Test Method D473 (API MPMS Chapter 10.1), shall be used.
Note 1—Test Method D4006 (API MPMS Chapter 10.2) has been determined to be the preferred and most accurate method for the determination of water.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements appear in 6.1, 8.3, and A1.5.4.
| ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| ASTM F 631 : 2015 | Standard Guide for Collecting Skimmer Performance Data in Controlled Environments |
| ASTM F 3350 : 2018 | Standard Guide for Collecting Skimmer Performance Data in Ice Conditions |
| ASTM D 665 : 2014-11 | TEST METHOD FOR RUST-PREVENTING CHARACTERISTICS OF INHIBITED MINERAL OIL IN THE PRESENCE OF WATER |
| API MPM CH10.5 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 10.5: STANDARD TEST METHOD FOR WATER IN PETROLEUM PRODUCTS AND BITUMINOUS MATERIALS BY DISTILLATION |
| API MPM CH10.4 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 10.4: DETERMINATION OF WATER AND/OR SEDIMENT IN CRUDE OIL BY THE CENTRIFUGE METHOD (FIELD PROCEDURE) |
| ISO 5272:1979 | Toluene for industrial use — Specifications |
| API MPM CH10.2 : 2016 | Determination of Water in Crude Oil by Distillation |
| API MPM CH8.1 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
| API MPM CH10.9 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 10.9: STANDARD TEST METHOD FOR WATER IN CRUDE OILS BY COULOMETRIC KARL FISCHER TITRATION |
| API MPM CH8.2 : 2016 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.2: STANDARD PRACTICE FOR AUTOMATIC SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.