ASTM D 396 : 2019 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Fuel Oils
Hardcopy , PDF
27-08-2020
English
15-12-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows:
1.1.1Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2 S15 are middle distillate fuels for use in domestic and small industrial burners. Grades No. 1 S5000, No. 1 S500, and No. 1 S15 are particularly adapted to vaporizing type burners or where storage conditions require low pour point fuel.
1.1.2Grades B6–B20 S5000, B6–B20 S500, and B6–B20 S15 are middle distillate fuel/biodiesel blends for use in domestic and small industrial burners.
1.1.3Grades No. 4 (Light) and No. 4 are heavy distillate fuels or middle distillate/residual fuel blends used in commercial/industrial burners equipped for this viscosity range.
1.1.4Grades No. 5 (Light), No. 5 (Heavy), and No. 6 are residual fuels of increasing viscosity and boiling range, used in industrial burners. Preheating is usually required for handling and proper atomization.
Note 1:For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
Note 2:A more detailed description of the grades of fuel oils is given in X1.3.
1.2This specification is for the use of purchasing agencies in formulating specifications to be included in contracts for purchases of fuel oils and for the guidance of consumers of fuel oils in the selection of the grades most suitable for their needs.
1.3Nothing in this specification shall preclude observance of federal, state, or local regulations which can be more restrictive.
1.4The values stated in SI units are to be regarded as standard.
1.4.1Non-SI units are provided in Table 1 and Table 2 and in 7.1.2.1/7.1.2.2 because these are common units used in the industry.
Note 3:The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5950 : 2014 | Standard Test Method for Pour Point of Petroleum Products (Automatic Tilt Method) |
| ASTM D 6892 : 2003 : R2020 | Standard Test Method for Pour Point of Petroleum Products (Robotic Tilt Method) |
| ASTM D 5950 : 2014 : R2020 | Standard Test Method for Pour Point of Petroleum Products (Automatic Tilt Method) |
| ASTM D 5985 : 2002 : R2014 | Standard Test Method for Pour Point of Petroleum Products (Rotational Method) |
| ASTM D 2887 : 2019 : REV A : EDT 1 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
| ASTM D 7039 : 2015 : REV A : R2020 | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 7039 : 2015 : REV A | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 6751 : 2020 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 7042 : 2019 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 5985 : 2002 : R2020 | Standard Test Method for Pour Point of Petroleum Products (Rotational Method) |
| ASTM D 7042 : 2016 : EDT 3 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 2887 : 2019 : REV A | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
| ASTM D 6892 : 2003 : R2014 | Standard Test Method for Pour Point of Petroleum Products (Robotic Tilt Method) |
| ASTM D 6751 : 2009 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.