ASTM D 3451 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Testing Coating Powders and Powder Coatings
Hardcopy , PDF
11-11-2014
English
01-06-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 06.02, 2017 Defines the selection and use of procedures for testing coating powders and powder coatings.
| Committee |
D 01
|
| DocumentType |
Guide
|
| Pages |
13
|
| ProductNote |
Reconfirmed 2006
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This guide covers the selection and use of procedures for testing coating powders and powder coatings. The test methods included are listed in . Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. Selection of the methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller.
1.2 This guide also refers to methods developed specifically for the coating powder industry by the Powder Coating Institute, PCI, and the International Organization for Standards, ISO.
1.3 This guide describes the testing of coating powders as applied by electrostatic spray, fluidized bed, or any other applicable method.
1.4
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 6441 : 2005 : R2016 | Standard Test Methods for Measuring the Hiding Power of Powder Coatings |
| ASTM D 5861 : 2007 : R2017 | Standard Guide for Significance of Particle Size Measurements of Coating Powders |
| ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 6695 : 2016 : REDLINE | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
| ISO 8130-13:2001 | Coating powders Part 13: Particle size analysis by laser diffraction |
| ASTM D 870 : 2015 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 1729 : 2016 : REDLINE | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ISO 8130-10:1998 | Coating powders Part 10: Determination of deposition efficiency |
| ISO 8130-5:1992 | Coating powders Part 5: Determination of flow properties of a powder/air mixture |
| ISO 8130-11:1997 | Coating powders Part 11: Inclined-plane flow test |
| ASTM G 153 : 2013 : REDLINE | Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
| ISO 8130-1:1992 | Coating powders Part 1: Determination of particle size distribution by sieving |
| ASTM D 609 : 2017 : REDLINE | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 660 : 1993 | Standard Test Method for Evaluating Degree of Checking of Exterior Paints |
| ISO 8130-2:1992 | Coating powders Part 2: Determination of density by gas comparison pyknometer (referee method) |
| ASTM D 5767 : 2017-09 | TEST METHODS FOR INSTRUMENTAL MEASUREMENT OF DISTINCTNESS-OF-IMAGE GLOSS OF COATING SURFACES |
| ASTM E 284 : 2017 : REDLINE | Standard Terminology of Appearance |
| ISO 8130-8:1994 | Coating powders Part 8: Assessment of the storage stability of thermosetting powders |
| ASTM D 1732 : 2003 | Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting |
| ASTM D 610 : 2008 | Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces |
| ASTM D 1921 : 2012-09 | TEST METHODS FOR PARTICLE SIZE (SIEVE ANALYSIS) OF PLASTIC MATERIALS |
| ASTM D 2244 : 2016 : REDLINE | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 661 : 1993 | Standard Test Method for Evaluating Degree of Cracking of Exterior Paints |
| ASTM D 2247 : 2015 : REDLINE | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM D 662 : 1993 | Standard Test Method for Evaluating Degree of Erosion of Exterior Paints |
| ASTM G 154 : 2016 : REDLINE | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
| ASTM G 152 : 2013 : REDLINE | Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
| ISO 8130-7:1992 | Coating powders Part 7: Determination of loss of mass on stoving |
| ASTM D 3134 : 2015 : REDLINE | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 1735 : 2014 : REDLINE | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 4587 : 2011 : REDLINE | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM D 7091 : 2013 : REDLINE | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM E 430 : 2011 : REDLINE | Standard Test Methods for Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry |
| ASTM G 155 : 2013 : REDLINE | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials |
| ASTM D 2794 : 1993 | TEST METHOD FOR RESISTANCE OF ORGANIC COATINGS TO THE EFFECTS OF RAPID DEFORMATION (IMPACT) |
| ISO 8130-9:1992 | Coating powders Part 9: Sampling |
| ASTM G 147 : 2017 : REDLINE | Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests |
| ISO 8130-12:1998 | Coating powders Part 12: Determination of compatibility |
| ASTM D 1474 : 1998 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 658 : 1991 | Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996) |
| ASTM D 522 : 1993 : REV A | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ISO 8130-14:2004 | Coating powders Part 14: Terminology |
| ASTM D 2454 : 2014-03 | PRACTICE FOR DETERMINING THE EFFECT OF OVERBAKING ON ORGANIC COATINGS |
| ASTM D 5531 : 2017 : REDLINE | Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings |
| ASTM D 3359 : 2017 : REDLINE | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM E 1331 : 2015 : REDLINE | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM D 1895 : 2017 : REDLINE | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials |
| ISO 8130-3:1992 | Coating powders Part 3: Determination of density by liquid displacement pyknometer |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.