ASTM D 3419 : 2012 : R2019
Current
The latest, up-to-date edition.
Standard Practice for In-Line Screw-Injection Molding Test Specimens From Thermosetting Compounds
Hardcopy , PDF
English
01-05-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.This practice covers the general principles to be followed when injection molding test specimens of thermosetting materials.
| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This practice covers the general principles to be followed when injection molding test specimens of thermosetting materials. It is to be used to obtain uniformity in methods of describing the various steps of the injection molding process and in the reporting of those conditions. The exact molding conditions will vary from material to material, and if not incorporated in the material specification, shall be agreed upon between the purchaser and the supplier or determined by previous experience with the particular type of material being used and its plasticity.
Note 1:The utility of this practice has been demonstrated for the molding of thermosetting molding compounds exhibiting lower-viscosity non-Newtonian flow.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This practice assumes the use of reciprocating screw injection molding machines.
Note 2:This standard and ISO 10724 address the same subject matter, but differ in technical content.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5948 : 2005 : R2012 | Standard Specification for Molding Compounds, Thermosetting |
| ASTM D 6289 : 2013 : R2019 | Standard Test Method for Measuring Shrinkage from Mold Dimensions of Molded Thermosetting Plastics |
| ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
| ASTM D 3641 : 2002 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 3641 : 2021 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2010 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2024 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2015 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2010 : REV A | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2014 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 1997 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2012 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.