ASTM D 3350 : 2024
Current
The latest, up-to-date edition.
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
Hardcopy , PDF
English
01-08-2024
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers the identification of polyethylene plastic pipe and fittings materials in accordance with a cell classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify manufacturing tolerances, or to determine suitability for use for a specific application.
1.1.1Some plastic pipe and fitting PE compounds classified by this standard are sold as a base material and then combined with other material(s) (for example, color or additive concentrate) by the pipe or fitting manufacturer into a final classified compound either prior to or during production of the final article. This standard, excluding the requirements of Table 1, properties 5 and 6, and 6.1.1, can be used for property verification of the incoming base material(s) in accordance with 8.1.
1.1.2In the case of PE compounds sold as the compound classified by the standard, see 8.1 regarding property verification of the incoming classified compound.
1.1.3Compounds with a cell classification value other than ‘0’ for the Hydrostatic Strength Classification (property 6) rely on a defined formulation. The composition of the defined formulation can be obtained from the owner of the formulation.
Note 1:Deviations from the defined formulation may affect the Hydrostatic Strength Classification.
1.2Polyethylene plastic materials, being thermoplastic, are reprocessable and recyclable (Note 3). This specification allows for the use of those polyethylene materials, provided that all specific requirements of this specification are met.
Note 2:The notes in this specification are for information only and shall not be considered part of this specification.
Note 3:See Guide D5033 for information and definitions related to recycled plastics.
1.3The values stated in SI units are to be regarded as standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 4:There is no known ISO equivalent to this standard.
1.5For information regarding molding and extrusion materials see Specification D4976. For information regarding wire and cable materials see Specification D1248.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2986 : 2023 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate, Heap Leach Aeration and Other Mining Applications |
| ASTM F 1412 : 2022 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F 2648/F2648M : 2023 | Standard Specification for 50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications |
| ASTM F 3565 : 2023 | Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service |
| ASTM E 3170/E3170M : 2018 : R2023 | Standard Practice for Phased Array Ultrasonic Testing of Polyethylene Electrofusion Joints |
| ASTM F 1282 : 2023 : REV A | Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe |
| ASTM F 2818 : 2010 : R2023 | Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing |
| ASTM F 2623 : 2024 : EDT 1 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
| ASTM F 1281 : 2024 | Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe |
| ASTM F 1055 : 2016 : REV A : R2022 | Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing |
| ASTM D 2737 : 2022 | Standard Specification for Polyethylene (PE) Plastic Tubing |
| ASTM E 3167/E3167M : 2018 : R2023 | Standard Practice for Conventional Pulse-Echo Ultrasonic Testing of Polyethylene Electrofusion Joints |
| ASTM E 3101 : 2018 | Standard Practice for Microwave Examination of Polyethylene Butt Fusion Joints |
| ASTM F 3506 : 2021 : EDT 1 | Standard Specification for Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe based on Inner Diameter (ID) for use in Air Conditioning and Refrigeration Line Set Systems |
| ASTM D 3261 : 2024 | Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing |
| ASTM F 3034 : 2021 | Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE) |
| ASTM F 2737 : 2011 : R2021 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units |
| ASTM F 2880 : 2021 | Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3</num><den>4</den></fraction > in. to 65 in. |
| ASTM D 2513 : 2020 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2306/F2306M : 2021 | Standard Specification for 300 mm to 1500 mm [12 in. to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Non-Pressure Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM E 3044/E3044M : 2022 | Standard Practice for Ultrasonic Testing of Polyethylene Butt Fusion Joints |
| ASTM F 3390 : 2020 | Standard Specification for 3 through 24 in. Lined Flexible Corrugated Polyethylene Pipe for Land Drainage Applications |
| ASTM F 1901 : 2022 | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| ASTM D 2239 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
| ASTM F 2805 : 2016 : R2022 | Standard Specification for Multilayer Thermoplastic And Flexible Steel Pipe And Connections |
| ASTM F 1759 : 1997 : R2024 | Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications |
| ASTM D 4883 : 2018 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique |
| ASTM F 810 : 2012 : R2024 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM F 412 : 2024 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2896 : 2023 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM D 7436 : 2017 : R2024 | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM E 2070 : 2023 | Standard Test Methods for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods |
| ASTM F 2769 : 2024 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems |
| ASTM F 894 : 2024 | Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe |
| ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
| ASTM F 3508 : 2021 : REV A | Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT) |
| ASTM F 2947/F2947M : 2021 : REV A | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM D 4703 : 2016 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 2046 : 2019 | Standard Test Method for Reaction Induction Time by Thermal Analysis |
| ASTM D 3485 : 2022 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM F 3346 : 2024 | Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe |
| ASTM F 3371 : 2022 | Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications |
| ASTM D 2683 : 2020 | Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing |
| ASTM D 4976 : 2012 : REV A : R2020 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM F 2021 : 2017 : R2022 | Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems |
| ASTM F 714 : 2024 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM F 2619/F2619M : 2020 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM C 1847 : 2021 | Standard Specification for Direct Buried Pre-Insulated and Jacketed Polyurethane Bonded Low Temperature Hot Water Piping Systems |
| ASTM F 1545 : 2015 : REV A : R2021 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges |
| ASTM F 2720/F2720M : 2020 | Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe |
| ASTM F 667/F667M : 2016 : R2021 | Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings |
| ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM F 2763/F2763M : 2016 : R2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2435 : 2022 | Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM E 2009 : 2023 | Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM D 3035 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM F 1606 : 2019 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
| ASTM E 1858 : 2023 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM D 1693 : 2021 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM F 1533 : 2020 | Standard Specification for Deformed Polyethylene (PE) Liner |
| ASTM F 2160 : 2022 : REV A | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 7001 : 2020 | Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications |
| ASTM F 2562/F2562M : 2024 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM F 3430 : 2020 | Standard Specification for Closed-Cell Cellular Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers |
| ASTM E 1860 : 2023 | Standard Test Method for Elapsed Time Calibration of Thermal Analyzers |
| ASTM E 3102 : 2018 | Standard Practice for Microwave Examination of Polyethylene Electrofusion Joints Used in Piping Application |
| ASTM F 3373 : 2021 | Standard Specification for Polyethylene (PE) Electrofusion Fittings for Outside Diameter Controlled Crosslinked Polyethylene (PEX) Pipe |
| ASTM F 2922 : 2013 : R2018 | Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.