ASTM D 333 : 2001 : R2021
Current
The latest, up-to-date edition.
Standard Guide for Clear and Pigmented Lacquers
Hardcopy , PDF
English
16-06-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 01
|
| DocumentType |
Guide
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover procedures for testing lacquers and lacquer coatings. The test methods included are listed in Table 1.
Note 1:In accordance with Terminology D16, a lacquer is defined as a coating composition that is based on synthetic thermoplastic film-forming material dissolved in organic solvent(s) and that dries primarily by solvent evaporation. Typical lacquers include those based on nitrocellulose, other cellulose derivatives, vinyl resins, acrylic resins, etc.
Note 2:Lacquers may be applied under such diverse conditions, to so many different surfaces, and their dried films may be subjected to so many kinds of wear and exposure that it is not possible to assure desired performance from a single selection of test methods and numerical results therefrom. Those skilled in lacquer technology may find partial assurance of obtaining desired qualities in various types of lacquers through careful selection of the methods covered herein and intelligent interpretation of results therefrom.
Note 3:It is intended ultimately to remove all experimental procedures from Test Methods D333 and to establish them as a guide to the selection of test methods for lacquer and perhaps to interpretation of results therefrom. Temporarily there remain in Test Methods D333 a few tests that are too short or otherwise presently unsuitable for establishment under separate ASTM designations.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 365 : 2001 : R2017 | Standard Guide for Soluble Nitrocellulose Base Solutions |
| ASTM D 3023 : 1998 : R2017 | Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents |
| ASTM D 3278 : 2020 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 2204 : 1965 : R1975 | Method of Test for Perspiration Resistance of Organic Coatings |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 772 : 2018 | Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints |
| ASTM D 2091 : 1996 : R2024 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 1735 : 2021 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 2244 : 2023 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 772 : 2024 | Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints |
| ASTM D 609 : 2017 : R2022 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 1200 : 2023 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 2805 : 2011 : R2018 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1200 : 2010 : R2018 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 2199 : 2003 : R2013 | Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D 445 : 2021 : EDT 2 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 93 : 2019 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 445 : 2017 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 1544 : 2004 : R2018 | Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) |
| ASTM D 16 : 2019 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM D 3278 : 2021 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 968 : 2022 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D 1644 : 2001 : R2017 | Standard Test Methods for Nonvolatile Content of Varnishes |
| ASTM D 1210 : 2005 : R2022 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1735 : 2014 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 56 : 2021 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 2199 : 2003 : R2021 | Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D 1210 : 2005 : R2014 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1535 : 2014 : R2018 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1644 : 2001 : R2023 | Standard Test Methods for Nonvolatile Content of Varnishes |
| ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 870 : 2015 : R2020 : EDT 1 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 16 : 2024 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM B 117 : 2019 | Standard Practice for Operating Salt Spray (Fog) Apparatus |
| ASTM D 870 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 1544 : 2004 : R2023 | Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) |
| ASTM D 445 : 2019 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 56 : 2021 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM E 308 : 2018 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 823 : 2018 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 445 : 2024 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 1729 : 2022 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 56 : 2022 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 2805 : 2011 : R2023 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 445 : 2018 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM E 308 : 2022 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 609 : 2017 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 1535 : 2014 : R2023 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 968 : 2017 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 659 : 1986 : EDT 1 | Method of Evaluating Degree of Chalking of Exterior Paints |
| ASTM D 823 : 2018 : R2022 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 16 : 2023 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM D 445 : 2023 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 93 : 2018 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.