ASTM D 3244 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
Hardcopy , PDF
08-06-2020
English
08-06-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Standard Practice
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers guidelines and statistical methodologies with which two parties, usually a supplier and a receiver, can compare and combine independently obtained test results to obtain an Assigned Test Value (ATV) for the purpose of resolving a product quality dispute.
1.2This practice defines a technique for establishing an Acceptance Limit (AL) to determine acceptance or rejection of the product in dispute by comparing an ATV to the AL.
1.3This practice applies only to those test methods which specifically state that the repeatability and reproducibility values conform to the definitions herein.
1.4The statistical principles and methodology outlined in this practice can also be used to obtain an ATV for specification conformance decision when multiple results are obtained for the same batch of product within a single laboratory. For this application, site precision (R') as defined in Practice D6299 shall be used in lieu of test method published reproducibility (R).
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7669 : 2020 | Standard Guide for Practical Lubricant Condition Data Trend Analysis |
| ASTM D 8350 : 2021 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine |
| ASTM D 1092 : 2020 | Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases |
| ASTM D 2265 : 2020 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 943 : 2020 | Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils |
| ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6792 : 2020 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 4485 : 2020 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 7320 : 2018 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 4950 : 2019 | Standard Classification and Specification for Automotive Service Greases |
| ASTM E 1458 : 2012 : R2016 | Standard Test Method for Calibration Verification of Laser Diffraction Particle Sizing Instruments Using Photomask Reticles |
| ASTM D 6792 : 2017 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM F 2508 : 2016 : EDT 1 | Standard Practice for Validation, Calibration, and Certification of Walkway Tribometers Using Reference Surfaces |
| ASTM D 2265 : 2019 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 6300 : 2020 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1092 : 2019 | Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases |
| ASTM D 943 : 2019 | Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils |
| ASTM D 8146 : 2018 | Standard Guide for Evaluating Test Method Capability and Fitness for Use |
| ASTM D 8111 : 2021 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
| ASTM D 6299 : 2021 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 2020 : REV B | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6299 : 2020 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 1319 : 2002 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.