ASTM D 3134 : 2015 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Establishing Color and Gloss Tolerances
Hardcopy , PDF
12-11-2024
English
01-11-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1.1This practice describes a procedure for establishing tolerances and evaluating the color and gloss of specimens with respect to specified standards. This practice is appropriate for nonfluorescent opaque specimens.
1.2This practice does not indicate the extent of tolerances, but gives guidance on how they can be set. For product specification, the tolerances between specimens and the specified standard should be agreed upon between the purchaser and the seller.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
E 12
|
| DocumentType |
Standard Practice
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes a procedure for establishing tolerances and evaluating the color and gloss of specimens with respect to specified standards. This practice is appropriate for nonfluorescent opaque specimens.
1.2This practice does not indicate the extent of tolerances, but gives guidance on how they can be set. For product specification, the tolerances between specimens and the specified standard should be agreed upon between the purchaser and the seller.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM D 5382 : 2002 : R2017 | Standard Guide to Evaluation of Optical Properties of Powder Coatings |
| ASTM D 7195 : 2016 : REV A | Standard Guide for Setting Object Color Specifications |
| ASTM D 5531 : 2017 | Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings |
| ASTM E 1499 : 2016 | Standard Guide for Selection, Evaluation, and Training of Observers |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM E 1808 : 1996 : R2015 | Standard Guide for Designing and Conducting Visual Experiments |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM E 1345 : 1998 : R2019 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 1535 : 2014 : R2018 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 3794 : 2022 | Standard Guide for Testing Coil Coatings |
| ASTM D 6577 : 2024 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM E 1808 : 1996 : R2021 | Standard Guide for Designing and Conducting Visual Experiments |
| ASTM E 1345 : 2024 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM D 7195 : 2021 | Standard Guide for Setting Object Color Specifications |
| ASTM D 3451 : 2024 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM E 805 : 2022 | Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1331 : 2015 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM E 1499 : 1997 | Standard Guide for Selection, Evaluation, and Training of Observers |
| ASTM D 3964 : 2010 : R2015 | Standard Practice for Selection of Coating Specimens for Appearance Measurements |
| ASTM D 3964 : 2010 : R2020 | Standard Practice for Selection of Coating Specimens for Appearance Measurements |
| ASTM D 2244 : 2023 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM E 1331 : 2015 : R2023 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 284 : 2022 | Standard Terminology of Appearance |
| ASTM D 5531 : 2017 : R2023 | Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings |
| ASTM E 1541 : 1998 | Standard Practice for Specifying and Matching Color Using the Colorcurve System |
| ASTM E 1164 : 1994 | Standard Practice for Obtaining Spectrophotometric Data for Object-Color Evaluation |
| ASTM E 805 : 2012 : REV A : R2017 | Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials |
| ASTM E 1164 : 2012 : R2023 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 1499 : 2016 : R2023 | Standard Guide for Selection, Evaluation, and Training of Observers |
| ASTM E 312 : 1996 | Standard Practice for Description and Selection of Conditions for Photographing Specimens |
| ASTM E 308 : 2018 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1164 : 2023 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM D 4449 : 2015 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
| ASTM D 4449 : 2015 : R2021 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
| ASTM E 1360 : 2005 : R2015 | Standard Practice for Specifying Color by Using the Optical Society of America Uniform Color Scales System |
| ASTM D 1729 : 2022 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM E 1345 : 1998 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM E 1331 : 2015 : R2019 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM E 1349 : 2006 : R2022 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry |
| ASTM E 308 : 2022 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 1535 : 2014 : R2023 | Standard Practice for Specifying Color by the Munsell System |
| ASTM E 1345 : 2024 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM E 1349 : 2006 : R2018 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry |
| ASTM E 1164 : 2012 : R2017 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 284 : 2017 | Standard Terminology of Appearance |
| ASTM E 1360 : 2005 : R2019 | Standard Practice for Specifying Color by Using the Optical Society of America Uniform Color Scales System |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.