ASTM D 2896 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration
04-01-2022
English
19-02-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.01, 2016 Specifies the determination of basic constituents in petroleum products by titration with perchloric acid in glacial acetic acid.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
12
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the determination of basic constituents in petroleum products by titration with perchloric acid in glacial acetic acid.
1.2Procedures A and B use different titration solvent volumes and sample weights.
Note 1:A round robin on a series of new and used oils and additive concentrates has shown that the two procedures give statistically equivalent results.
1.3Appendix X2 provides the use of an alternative solvent system which eliminates the use of chlorobenzene in this test method. The use of the alternative solvent gives statistically equivalent results; however, the precision is worse. Paragraph X2.5.5 provides guidance when comparing results using the two different solvents.
1.4The constituents that may be considered to have basic characteristics include organic and inorganic bases, amino compounds, salts of weak acids (soaps), basic salts of polyacidic bases, and salts of heavy metals.
Note 2:This test method is applicable to both fresh oils and used oils as described in Sections 16, 17, and 19 and Appendix X1.
1.5This test method can be used to determine base number >300 mg KOH/g. However, the precision statement in Section 19 has been obtained only on base number ≤300 mg KOH/g.
1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7, Section 10, and X2.2.
| SAE AMS 2980/4 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 4 - PURCHASING SPECIFICATION - RESIN |
| MIL-L-46152 Revision E:1990 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, ADMINISTRATIVE SERVICE, METRIC |
| MIL PRF 009000 : K | LUBRICATING OIL, SHIPBOARD INTERNAL COMBUSTION ENGINE, HIGH-OUTPUT DIESEL |
| MIL L 21260 : D | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATIVE AND BREAK IN |
| MIL-PRF-46167 Revision D:2005 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, ARCTIC |
| MIL-PRF-9000 Revision L:2014 | Lubricating Oil, Shipboard Internal Combustion Engine, High-Output Diesel |
| ASTM D 7415 : 2018 : REDLINE | Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| SAE AMS 2950/1 : 2008 | PASTE ADHESIVE FOR CORE RESTORATION - PART 1: GENERAL REQUIREMENTS |
| ASTM D 3712 : 2005 : R2017 | Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography |
| SAE MS 1005 : 2017 | LUBRICANTS, INDUSTRIAL OILS, AND RELATED PRODUCTS TYPE HF FIRE-RESISTANT HYDRAULIC FLUIDS - SPECIFICATION |
| ASTM D 8126 : 2017 | Standard Test Method for Efficient Basicity Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 6975 : 2004 : R2010 | Standard Test Method for Cummins M11 EGR Test (Withdrawn 2019) |
| A-A-52306 Revision A:1995 | LUBRICATING OIL, HEAVY-DUTY DIESEL ENGINE |
| ASTM D 7624 : 2010 | Standard Test Method for Condition Monitoring of Nitration in In-Service Petroleum and Hydrocarbon-Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| 01/707860 DC : DRAFT MAY 2001 | ISO/DIS 14830-1 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - TRIBOLOGY-BASED MONITORING AND DIAGNOSTICS - PART 1: GENERAL GUIDELINES |
| ASTM D 4859 : 2013 : REDLINE | Standard Specification for Lubricants for Two-Stroke-Cycle Spark-Ignition Gasoline Engines-TC |
| ASTM D 4681 : 1987 | Specification For Lubricants For Two-Stroke-Cycle Gasoline Engines- (TSC-4) (Withdrawn 1995) |
| SAE J 2359 : 1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, MILITARY COMBAT/TACTICAL SERVICE |
| ASTM D 5984 : 2011 : R2017 | Standard Test Method for Semi-Quantitative Field Test Method for Base Number in New and Used Lubricants by Color-Indicator Titration |
| ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 6074 : 2015 : REDLINE | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
| ASTM D 6838 : 2004 : R2010 | Standard Test Method for Cummins M11 High Soot Test (Withdrawn 2019) |
| ASTM D 6975 : 2004 | Standard Test Method for Cummins M11 EGR Test |
| MIL-PRF-21260 Revision E:1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATIVE BREAK-IN |
| ASTM D 7417 : 2017 : REDLINE | Standard Test Method for Analysis of In-Service Lubricants Using Particular Four-Part Integrated Tester (Atomic Emission Spectroscopy, Infrared Spectroscopy, Viscosity, and Laser Particle Counter) |
| SAE J 2361 : 1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATION BREAK-IN |
| ASTM D 7596 : 2014 : REDLINE | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
| ASTM D 5984 : 2011 | Standard Test Method for Semi-Quantitative Field Test Method for Base Number in New and Used Lubricants by Color-Indicator Titration |
| ASTM D 3712 : 2005 : R2011 | Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography |
| ISO 18436-5:2012 | Condition monitoring and diagnostics of machines — Requirements for qualification and assessment of personnel — Part 5: Lubricant laboratory technician/analyst |
| ASTM E 2412 : 2010 | Standard Practice for Condition Monitoring of Used Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| ASTM D 4858 : 2013 : REDLINE | Standard Test Method for Determination of the Tendency of Lubricants to Promote Preignition in Two-Stroke-Cycle Gasoline Engines |
| BS ISO 18436-5:2012 | Condition monitoring and diagnostics of machines. Requirements for qualification and assessment of personnel Lubricant laboratory technician/analyst |
| ASTM D 7414 : 2018 : REDLINE | Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| DEFSTAN 91-43/2(1993) : 1993 | LUBRICATING OIL, ENGINE: GRADE 50 NATO CODE NO. 0-182 JOINT SERVICE DESIGNATION: OMD-330 |
| ASTM D 3712 : 2005 | Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography |
| SAE AMS 2950/1 : 2008(R2019) | PASTE ADHESIVE FOR CORE RESTORATION - PART 1: GENERAL REQUIREMENTS |
| ASTM D 7412 : 2018 : REDLINE | Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| ASTM D 4863 : 2013 : REDLINE | Standard Test Method for Determination of Lubricity of Two-Stroke-Cycle Gasoline Engine Lubricants |
| ASTM D 7844 : 2018 : REDLINE | Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry |
| 08/30190684 DC : DRAFT OCT 2008 | BS ISO 18436-5 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - REQUIREMENTS FOR QUALIFICATION AND ASSESSMENT OF PERSONNEL - PART 5: LUBRICANT LABORATORY TECHNICIAN/ANALYST |
| MIL L 9000 : H | LUBRICATING OIL, SHIPBOARD INTERNAL COMBUSTION ENGINE, HIGH OUTPUT DIESEL |
| MIL L 2104 : F | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT TACTICAL SERVICE |
| ASTM D 7720:2011 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| SAE AMS 2980/1 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 1 - GENERAL REQUIREMENTS |
| SAE MS 1000 : 2013 | LUBRICANTS, INDUSTRIAL OILS, AND RELATED PRODUCTS - CLASSIFICATION |
| ASTM D 6838 : 2004 | Standard Test Method for Cummins M11 High Soot Test |
| UNI ISO 18436-5 : 2013 | CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - REQUIREMENTS FOR QUALIFICATION AND ASSESSMENT OF PERSONNEL - PART 5: LUBRICANT LABORATORY TECHNICIAN/ANALYST |
| SAE J 357 : 2016 | PHYSICAL AND CHEMICAL PROPERTIES OF ENGINE OILS |
| ASTM D 4739 : 2017 : REDLINE | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 6483 : 2004 | Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine (Withdrawn 2009) |
| ASTM D 6224 : 2016 : REDLINE | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
| ASTM E 2412 : 2010 : R2018 | Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.