ASTM D 2777 : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water
28-06-2022
English
11-03-2013
CONTAINED IN VOL. 11.01, 2017 Describes uniform standards for estimating and expressing the precision and bias of applicable test methods for Committee D19 on Water.
Committee |
D 19
|
DocumentType |
Redline
|
Pages |
21
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This practice establishes uniform standards for estimating and expressing the precision and bias of applicable test methods for Committee D19 on Water. Statements of precision and bias in test methods are required by the Form and Style for ASTM Standards, “Section A21. Precision and Bias (Mandatory).” In principle, all test methods are covered by this practice.
1.2Except as specified in 1.4, 1.5, and 1.6, this practice requires the task group proposing a new test method to carry out a collaborative study from which statements for precision (overall and single-operator standard-deviation estimates) and bias can be developed. This practice provides general guidance to task groups in planning and conducting such determinations of precision and bias.
1.3This practice also provides guidance to task groups for conducting limited-scale collaborative studies (known as “comparability studies”) for test methods that have been revised, when such revision includes substantive modifications. Examples of substantive modifications may include, but are not limited to, changes in mandatory or allowable instrumentation, reagents, reaction times, etc.
1.3.1Changes to applicable water matrices in the Scope of a method may constitute a substantive modification under this provision. However, recognize that even the original collaborative study may not have used all the various matrix types specified in the method’s original Scope.
1.3.2A method's concentration-range extension that is deemed to merit additional collaborative testing (even without a method modification that would otherwise be considered substantive) shall require a full collaborative study, as described in Sections 7.1-7.5, but only at Youden-pair concentrations representative of the extended range. Note that such a collaborative study could involve as little as a single-sample Youden-pair study in a single reproducible matrix.
1.4If a full-scale collaborative study is not technically feasible, due to the nature of the test method or instability of samples, the largest feasible scaled-down collaborative study shall be conducted to provide the best possible limited basis for estimating the overall and single-operator standard deviations.
1.4.1Examples of acceptable scaled-down studies are the local-area studies conducted by Subcommittee D19.24 on microbiological methods because of inherent sample instability. These studies involve six or more completely independent local-area analysts who can begin analysis of uniform samples at an agreed upon time.
1.4.2If uniform samples are not feasible under any circumstances, a statement of single-operator precision will meet the requirements of this practice. Whenever possible, this statement should be developed from data generated by independent multiple operators, each doing replicate analyses on independent samples (of a specific matrix type), which generally fall within specified concentration ranges (see 7.2.5.2 (3)).
1.5A collaborative study that satisfied the requirements of the version of this practice in force when the study was conducted will continue to be considered an adequate basis for the precision-and-bias statement required in each test method. If the study does not satisfy the current minimum requirements for a collaborative study, a statement listing the study's deficiencies and a reference to this paragraph shall be included in the precision-and-bias statement as the basis for an exemption from the current requirements.
1.6This paragraph relates to special exemptions not clearly acceptable under 1.4 or 1.5. With the approval of Committee D19 on the recommendation of the Results Advisor and the Technical Operations Section of the Executive Subcommittee of Committee D19, a statement giving a compelling reason why compliance with all or specific points of this practice cannot be achieved will meet both ASTM requirements (1)2 and the related requirements of this practice. In addition, Committee D19, through a Main Committee ballot, may approve publication of a “Preliminary” Standard Method for a period not to exceed 5 years. Preliminary Standards must contain a minimum of a single-operator precision-and-bias statement and a Quality Control section based on the single operator data. Publication of a Preliminary Standard is conditional on the approval of a full D2777 collaborative study design for the standard. Precision-and-bias statements authorized by this paragraph shall include the date of approval by Committee D19.
1.7Per Section A21.2.3 of the ASTM Form and Style Manual the committee may delay an interlaboratory study for a new method and include a temporary statement in the Precision and Bias Section that addresses only single operator precision (“repeatability”). This statement is valid for five years from the initial publication date. In this case, a single laboratory study shall be conducted in accordance with Section 7.6.
1.8In Section 12 this practice shows exemplary precision-and-bias-statement formats for: (1) test methods yielding a numerical measure, (2) test methods yielding a non-numerical report of success or failure based on criteria specified in the procedure, and (3) test methods specifying that procedures in another ASTM test method are to be used with only insignificant modifications.
1.9All studies, even those exempt from some requirements under Sections 1.4 through 1.8, shall receive approval from the Results Advisor before being conducted (see Section 8) and after completion (see Section 13).
1.10This practice satisfies the QC requirements of Practice D5847.
ASTM D 6908 : 2006 : R2017 | Standard Practice for Integrity Testing of Water Filtration Membrane Systems |
ASTM D 5243 : 1992 : R2001 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly at Culverts |
ASTM D 5627 : 2017 : REDLINE | Standard Test Method for Water Extractable Residue from Particulate Ion-Exchange Resins |
ASTM D 5390 : 1993 : R2007 | Standard Test Method for Open-Channel Flow Measurement of Water with Palmer-Bowlus Flumes |
ASTM D 5086 : 2001 | Standard Test Method for Determination of Calcium, Magnesium, Potassium, and Sodium in Atmospheric Wet Deposition by Flame Atomic Absorption Spectrophotometry |
ASTM D 5389 : 1993 : R2002 | Standard Test Method for Open-Channel Flow Measurement by Acoustic Velocity Meter Systems |
ASTM D 5176 : 2008 : R2015 | Standard Test Method for Total Chemically Bound Nitrogen in Water by Pyrolysis and Chemiluminescence Detection |
ASTM D 7599 : 2016 : R2017 | Standard Test Method for Determination of Diethanolamine, Triethanolamine, <emph type="ital">N</emph>-Methyldiethanolamine and <emph type="ital">N</emph >-Ethyldiethanolamine in Water by Single Reaction Monitoring Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 5412 : 1993 : R2011 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
ASTM D 5284 : 2009 | Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid |
ASTM D 5905 : 1998 : R2018 | Standard Practice for the Preparation of Substitute Wastewater |
ASTM D 3357 : 1983 | Method of Test for Radioactive Nickel in Water (Withdrawn 1989 |
ASTM D 7511 : 2012 | Standard Test Method for Total Cyanide by Segmented Flow Injection Analysis, In-Line Ultraviolet Digestion and Amperometric Detection |
ASTM D 5847 : 2002 : R2007 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
ASTM D 7645 : 2016 : REDLINE | Standard Test Method for Determination of Aldicarb, Aldicarb Sulfone, Aldicarb Sulfoxide, Carbofuran, Methomyl, Oxamyl, and Thiofanox in Water by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 5612 : 1994 : R2008 | Standard Guide for Quality Planning and Field Implementation of a Water Quality Measurement Program |
ASTM D 4790 : 2014 : REDLINE | Standard Terminology of Aromatic Hydrocarbons and Related Chemicals |
ASTM D 4793 : 2009 | Standard Test Method for Sequential Batch Extraction of Waste with Water |
ASTM D 6697 : 2001 | Standard Test Method for Determination for Chemical Oxygen Demand (Manganese III Oxygen Demand) of Water (Withdrawn 2010) |
ASTM D 5412 : 1993 : R2011 : EDT 1 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
ASTM D 2972 : 2015 : REDLINE | Standard Test Methods for Arsenic in Water |
ASTM D 5390 : 1993 : R2013 | Standard Test Method for Open-Channel Flow Measurement of Water with Palmer-Bowlus Flumes |
ASTM D 4409 : 1995 : R1999 | Standard Test Method for Velocity Measurements of Water in Open Channels with Rotating Element Current Meters |
ASTM D 5905 : 1998 : R2008 | Standard Practice for the Preparation of Substitute Wastewater |
ASTM D 3865 : 2009 : R2015 | Standard Test Method for Plutonium in Water (Withdrawn 2024) |
ASTM D 3921 : 1996 : R2011 | Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water (Withdrawn 2013) |
ASTM D 1890 : 2015 | Standard Test Method for Beta Particle Radioactivity of Water  |
ASTM D 7573 : 2009 | Standard Test Method for Total Carbon and Organic Carbon in Water by High Temperature Catalytic Combustion and Infrared Detection |
ASTM D 888 : 2012-05 | TEST METHODS FOR DISSOLVED OXYGEN IN WATER |
ASTM D 5072 : 2009 : R2016 | Standard Test Method for Radon in Drinking Water |
ASTM D 6592 : 2001 | Standard Test Method for Portable Chemiluminescent Water Quality Determination (Withdrawn 2010) |
ASTM D 7678 : 2017 : REDLINE | Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbons (TPH) in Water and Wastewater with Solvent Extraction using Mid-IR Laser Spectroscopy |
ASTM F 569 : 1978 : R1982 | Classification for Filterability Index of Reagent-Grade Water and High-Purity Waters for Microelectronic Device Processing |
ASTM D 3373 : 2017 : REDLINE | Standard Test Method for Vanadium in Water |
ASTM D 6512 : 2007 | Standard Practice for Interlaboratory Quantitation Estimate |
ASTM D 5243 : 1992 : R1996 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly at Culverts |
ASTM D 3975 : 1993 : R2014 | Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments |
ASTM D 4519 : 2016 : REDLINE | Standard Test Method for On-Line Determination of Anions and Carbon Dioxide in High Purity Water by Cation Exchange and Degassed Cation Conductivity |
ASTM D 5256 : 2014 : REDLINE | Standard Test Method for Relative Efficacy of Dynamic Solvent Systems for Dissolving Water-Formed Deposits |
ASTM D 3975 : 1993 : R2003 | Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments |
ASTM D 3113 : 1992 : R1998 | Standard Test Methods for Sodium Salts of EDTA in Water (Withdrawn 2005) |
ASTM D 3670 : 1991 : R2001 | Standard Guide for Determination of Precision and Bias of Methods of Committee D22 |
ASTM D 5390 : 1993 | TEST METHOD FOR OPEN-CHANNEL FLOW MEASUREMENT OF WATER WITH PALMER-BOWLUS FLUMES |
ASTM D 5811 : 2008 : R2013 | Standard Test Method for Strontium-90 in Water |
ASTM D 7979 : 2017 : REDLINE | Standard Test Method for Determination of Per- and Polyfluoroalkyl Substances in Water, Sludge, Influent, Effluent and Wastewater by Liquid Chromatography Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 4332 : 2014 : REDLINE | Standard Practice for Conditioning Containers, Packages, or Packaging Components for Testing |
ASTM D 5831 : 2017 : REDLINE | Standard Practice for Screening Fuels in Soils |
ASTM D 6317 : 2015 : REDLINE | Standard Test Method for Low Level Determination of Total Carbon, Inorganic Carbon and Organic Carbon in Water by Ultraviolet, Persulfate Oxidation, and Membrane Conductivity Detection |
ASTM D 5129 : 1995 : R2014 | Standard Test Method for Open Channel Flow Measurement of Water Indirectly by Using Width Contractions |
ASTM D 3977 : 1997 : R2002 | Standard Test Methods for Determining Sediment Concentration in Water Samples |
ASTM D 4130 : 2015 : REDLINE | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
ASTM D 5242 : 1992 : R2007 | Standard Test Method for Open-Channel Flow Measurement of Water with Thin-Plate Weirs |
ASTM D 1941 : 1991 : R2007 | Standard Test Method for Open Channel Flow Measurement of Water with the Parshall Flume |
ASTM F 316 : 2003 : R2011 | Standard Test Methods for Pore Size Characteristics of Membrane Filters by Bubble Point and Mean Flow Pore Test |
ASTM D 5129 : 1995 : R1999 | Standard Test Method for Open Channel Flow Measurement of Water Indirectly by Using Width Contractions |
ASTM D 5089 : 1995 : R2008 | Standard Test Method for Velocity Measurements of Water in Open Channels with Electromagnetic Current Meters |
ASTM D 5129 : 1995 : R2014 : EDT 1 | Standard Test Method for Open Channel Flow Measurement of Water Indirectly by Using Width Contractions (Withdrawn 2023) |
ASTM D 5388 : 1993 : R2007 | Standard Test Method for Indirect Measurements of Discharge by Step-Backwater Method |
ASTM D 2791 : 2013 : REDLINE | Standard Test Method for On-line Determination of Sodium in Water |
ASTM D 1125 : 2014 : REDLINE | Standard Test Methods for Electrical Conductivity and Resistivity of Water (Withdrawn 2023) |
ASTM D 3649 : 2006 : R2014 | Standard Practice for High-Resolution Gamma-Ray Spectrometry of Water (Withdrawn 2023) |
ASTM D 5412 : 1993 : R2005 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
ASTM D 7600 : 2016 : R2017 | Standard Test Method for Determination of Aldicarb, Carbofuran, Oxamyl and Methomyl by Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 5413 : 1993 : R2002 | Standard Test Methods for Measurement of Water Levels in Open-Water Bodies |
ASTM D 5916 : 1996 : R2002 | Standard Test Method for Detection and Enumeration of <i>Clostridium perfringens</i> from Water and Extracted Sediments by Membrane Filtration (MF) (Withdrawn 2011) |
ASTM D 4922 : 2009 : R2016 : EDT 1 | Standard Test Method for Determination of Radioactive Iron in Water |
ASTM D 5811 : 2008 | Standard Test Method for Strontium-90 in Water |
ASTM D 3856 : 2011 | Standard Guide for Management Systems in Laboratories Engaged in Analysis of Water |
ASTM D 5391 : 2014 : REDLINE | Standard Test Method for Electrical Conductivity and Resistivity of a Flowing High Purity Water Sample (Withdrawn 2023) |
ASTM D 4778 : 2015 : REDLINE | Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024) |
ASTM D 5614 : 1994 : R2008 | Standard Test Method for Open Channel Flow Measurement of Water with Broad-Crested Weirs |
ASTM D 6502 : 2010 : R2015 | Standard Test Method for Measurement of On-line Integrated Samples of Low Level Suspended Solids and Ionic Solids in Process Water by X-Ray Fluorescence (XRF) |
ASTM D 6234 : 2013 : REDLINE | Standard Test Method for Shake Extraction of Mining Waste by the Synthetic Precipitation Leaching Procedure |
ASTM D 7575 : 2011 | Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination |
ASTM E 1600 : 2015 : REDLINE | Standard Test Methods for Determination of Gold in Cyanide Solutions |
ASTM D 5613 : 1994 : R2008 | Standard Test Method for Open-Channel Measurement of Time of Travel Using Dye Tracers |
ASTM D 1783 : 2001 : R2007 | Standard Test Methods for Phenolic Compounds in Water |
ASTM D 5413 : 1993 : R2013 | Standard Test Methods for Measurement of Water Levels in Open-Water Bodies |
ASTM D 3977 : 1997 : R2013 : EDT 1 | Standard Test Methods for Determining Sediment Concentration in Water Samples |
ASTM D 6501 : 2015 : REDLINE | Standard Test Method for Phosphonate in Brines |
ASTM D 5242 : 1992 | TEST METHOD FOR OPEN-CHANNEL FLOW MEASUREMENT OF WATER WITH THIN-PLATE WEIRS |
ASTM D 3977 : 1997 | Standard Test Methods for Determining Sediment Concentration in Water Samples |
ASTM D 3591 : 2017 : REDLINE | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
ASTM D 1691 : 2017 : REDLINE | Standard Test Methods for Zinc in Water |
ASTM D 6569 : 2014 : REDLINE | Standard Test Method for On-Line Measurement of pH (Withdrawn 2023) |
ASTM D 511 : 2014 : REDLINE | Standard Test Methods for Calcium and Magnesium In Water |
ASTM D 1783 : 2001 : R2012 : EDT 1 | Standard Test Methods for Phenolic Compounds in Water |
ASTM D 4458 : 2015 : REDLINE | Standard Test Method for Chloride Ions in Brackish Water, Seawater, and Brines |
ASTM D 7575 : 2011 : R2017 | Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination |
ASTM D 4839 : 2003 : R2011 | Standard Test Method for Total Carbon and Organic Carbon in Water by Ultraviolet, or Persulfate Oxidation, or Both, and Infrared Detection |
ASTM D 512 : 2012 | Standard Test Methods for Chloride Ion In Water (Withdrawn 2021) |
ASTM D 1253 : 2014 : REDLINE | Standard Test Method for Residual Chlorine in Water |
ASTM F 316:2003 | Standard Test Methods for Pore Size Characteristics of Membrane Filters by Bubble Point and Mean Flow Pore Test |
ASTM D 1252 : 2006 : R2012 : EDT 1 | Standard Test Methods for Chemical Oxygen Demand (Dichromate Oxygen Demand) of Water |
ASTM D 5904 : 2002 | Standard Test Method for Total Carbon, Inorganic Carbon, and Organic Carbon in Water by Ultraviolet, Persulfate Oxidation, and Membrane Conductivity Detection |
ASTM D 5543 : 2015 : REDLINE | Standard Test Method for Low-Level Dissolved Oxygen in Water |
ASTM D 8083 : 2016 | Standard Test Method for Total Nitrogen, and Total Kjeldahl Nitrogen (TKN) by Calculation, in Water by High Temperature Catalytic Combustion and Chemiluminescence Detection |
ASTM D 1943 : 2005 : R2012 | Standard Test Method for Alpha Particle Radioactivity of Water |
ASTM D 5464 : 2016 : REDLINE | Standard Test Method for pH Measurement of Water of Low Conductivity |
ASTM D 4841 : 1988 : R2013 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
ASTM D 6512 : 2007 : R2014 | Standard Practice for Interlaboratory Quantitation Estimate (Withdrawn 2023) |
ASTM D 4409 : 1995 : R2003 | Standard Test Method for Velocity Measurements of Water in Open Channels with Rotating Element Current Meters |
ASTM D 4841 : 1988 : R2008 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
ASTM D 6238 : 1998 : R2017 | Standard Test Method for Total Oxygen Demand in Water |
ASTM D 1973 : 1991 | Standard Guide for Design of a Liner System for Containment of Wastes (Withdrawn 2000) |
ASTM D 5129 : 1995 : R2008 | Standard Test Method for Open Channel Flow Measurement of Water Indirectly by Using Width Contractions |
ASTM D 3670 : 1991 : R1996 : EDT 1 | Standard Guide for Determination of Precision and Bias of Methods of Committee D22 |
ASTM D 4412 : 2015 : REDLINE | Standard Test Methods for Sulfate-Reducing Bacteria in Water and Water-Formed Deposits |
ASTM D 3975 : 1993 : R2008 | Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments |
ASTM D 3972 : 2009 | Standard Test Method for Isotopic Uranium in Water by Radiochemistry |
ASTM D 3557 : 2017 : REDLINE | Standard Test Methods for Cadmium in Water |
ASTM D 4193 : 2008 : R2013 : EDT 1 | Standard Test Method for Thiocyanate in Water |
ASTM D 1246 : 2016 : REDLINE | Standard Test Method for Bromide Ion in Water |
ASTM D 4743 : 1992 : R1996 | Standard Test Method for Efficacy of Solvent Systems for Dissolving Water-Formed Deposits (Withdrawn 2003) |
ASTM D 5317 : 1998 : R2011 | Standard Test Method for Determination of Chlorinated Organic Acid Compounds in Water by Gas Chromatography with an Electron Capture Detector |
ASTM D 3858 : 1995 : R2008 | Standard Test Method for Open-Channel Flow Measurement of Water by Velocity-Area Method |
ASTM D 5413 : 1993 : R1997 | Standard Test Methods for Measurement of Water Levels in Open-Water Bodies |
ASTM D 1292 : 2015 : REDLINE | Standard Test Method for Odor in Water |
ASTM D 3856 : 2011 : R2015 | Standard Guide for Management Systems in Laboratories Engaged in Analysis of Water (Withdrawn 2024) |
ASTM D 5390 : 1993 : R1997 | Standard Test Method for Open Channel Flow Measurement of Water with Palmer-Bowlus Flumes |
ASTM D 3223 : 2017 : REDLINE | Standard Test Method for Total Mercury in Water |
ASTM D 5388 : 1993 : R1997 | Standard Test Method for Indirect Measurements of Discharge by Step-Backwater Method |
ASTM D 2460 : 2007 | Standard Test Method for Alpha-Particle-Emitting Isotopes of Radium in Water |
ASTM D 3975 : 1993 : R1999 | Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments |
ASTM D 3858 : 1995 : R1999 | Standard Test Method for Open-Channel Flow Measurement of Water by Velocity-Area Method |
ASTM D 5176 : 2008 | Standard Test Method for Total Chemically Bound Nitrogen in Water by Pyrolysis and Chemiluminescence Detection |
ASTM D 6091 : 2007 | Standard Practice for 99 %/95 % Interlaboratory Detection Estimate (IDE) for Analytical Methods with Negligible Calibration Error |
ASTM D 858 : 2017 : REDLINE | Standard Test Methods for Manganese in Water |
ASTM D 5242 : 1992 : R2013 | Standard Test Method for Open-Channel Flow Measurement of Water with Thin-Plate Weirs |
ASTM D 8002 : 2015 : EDT 1 | Standard Test Method for Modified Fouling Index (MFI-0.45) of Water (Withdrawn 2024) |
ASTM D 5412 : 1993 : R2000 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
ASTM D 6908 : 2006 : R2010 | Standard Practice for Integrity Testing of Water Filtration Membrane Systems |
ASTM D 6502 : 2010 | Standard Test Method for Measurement of On-line Integrated Samples of Low Level Suspended Solids and Ionic Solids in Process Water by X-Ray Fluorescence (XRF) |
ASTM D 7511 : 2012 : R2017 : EDT 1 | Standard Test Method for Total Cyanide by Segmented Flow Injection Analysis, In-Line Ultraviolet Digestion and Amperometric Detection |
ASTM D 5613 : 1994 : R2014 | Standard Test Method for Open-Channel Measurement of Time of Travel Using Dye Tracers (Withdrawn 2023) |
ASTM D 7783 : 2013 | Standard Practice for Within-laboratory Quantitation Estimation (WQE) |
ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
ASTM D 859 : 2016 : REDLINE | Standard Test Method for Silica in Water |
ASTM D 5085 : 2002 : R2008 | Standard Test Method for Determination of Chloride, Nitrate, and Sulfate in Atmospheric Wet Deposition by Chemically Suppressed Ion Chromatography |
ASTM D 7363 : 2013 | Standard Test Method for Determination of Parent and Alkyl Polycyclic Aromatics in Sediment Pore Water Using Solid-Phase Microextraction and Gas Chromatography/Mass Spectrometry in Selected Ion Monitoring Mode |
ASTM D 6071 : 2014 : REDLINE | Standard Test Method for Low Level Sodium in High Purity Water by Graphite Furnace Atomic Absorption Spectroscopy |
ASTM D 8024 : 2016 | Standard Test Method for Determination of (Tri-n-butyl)-n-tetradecylphosphonium chloride (TTPC) in Water by Multiple Reaction Monitoring Liquid Chromatography/Mass Spectrometry (LC/MS/MS) |
ASTM D 1339 : 1984 | Methods of Test for Sulfite Ion in Water (Withdrawn 1988) |
ASTM D 5130 : 1995 : R2003 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method |
ASTM D 5790 : 1995 : R2001 | Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry |
ASTM D 2038 : 1983 | Test for Radioactive Barium in Water (Withdrawn 1987) |
ASTM D 7597 : 2016 | Standard Test Method for Determination of Diisopropyl Methylphosphonate, Ethyl Hydrogen Dimethylamidophosphate, Ethyl Methylphosphonic Acid, Isopropyl Methylphosphonic Acid, Methylphosphonic Acid and Pinacolyl Methylphosphonic Acid in Water by Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 7284 : 2013 : R2017 | Standard Test Method for Total Cyanide in Water by Micro Distillation followed by Flow Injection Analysis with Gas Diffusion Separation and Amperometric Detection |
ASTM D 1687 : 2017 : REDLINE | Standard Test Methods for Chromium in Water |
ASTM D 7677 : 2016 : REDLINE | Standard Test Method for the Continuous Measurement of Dissolved Ozone in Low Conductivity Water |
ASTM D 5089 : 1995 : R2014 | Standard Test Method for Velocity Measurements of Water in Open Channels with Electromagnetic Current Meters (Withdrawn 2023) |
ASTM D 7644 : 2016 : REDLINE | Standard Test Method for Determination of Bromadiolone, Brodifacoum, Diphacinone and Warfarin in Water by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 1783 : 2001 | Standard Test Methods for Phenolic Compounds in Water |
ASTM D 6238 : 1998 : R2011 | Standard Test Method for Total Oxygen Demand in Water |
ASTM D 3921 : 1996 | Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water |
ASTM D 5475 : 1993 : R1997 | Standard Test Method for Nitrogen- and Phosphorus-Containing Pesticides in Water by Gas Chromatography with a Nitrogen-Phosphorus Detector |
ASTM D 5130 : 1995 : R2014 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method (Withdrawn 2023) |
ASTM D 7730 : 2017 : REDLINE | Standard Test Method for Determination of Dioctyl Sulfosuccinate in Sea Water by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 5612 : 1994 : R2018 | Standard Guide for Quality Planning and Field Implementation of a Water Quality Measurement Program |
ASTM D 5388 : 1993 : R2002 | Standard Test Method for Indirect Measurements of Discharge by Step-Backwater Method |
ASTM D 1783 : 2001 : R2012 | Standard Test Methods for Phenolic Compounds in Water |
ASTM D 7363 : 2013 : REV A | Standard Test Method for Determination of Parent and Alkyl Polycyclic Aromatics in Sediment Pore Water Using Solid-Phase Microextraction and Gas Chromatography/Mass Spectrometry in Selected Ion Monitoring Mode |
ASTM D 5390 : 1993 : R2002 | Standard Test Method for Open-Channel Flow Measurement of Water with Palmer-Bowlus Flumes |
ASTM D 4282 : 2015 : REDLINE | Standard Test Method for Determination of Free Cyanide in Water and Wastewater by Microdiffusion |
ASTM D 3352 : 2015 : REDLINE | Standard Test Method for Strontium Ion in Brackish Water, Seawater, and Brines |
ASTM E 1625 : 1994 : R2008 | Standard Test Method for Determining Biodegradability of Organic Chemicals in Semi-Continuous Activated Sludge (SCAS) (Withdrawn 2013) |
ASTM D 7066 : 2004 : R2017 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
ASTM D 6301 : 2013 : REDLINE | Standard Practice for Collection of On-Line Composite Samples of Suspended Solids and Ionic Solids in Process Water |
ASTM D 5257 : 2017 : REDLINE | Standard Test Method for Dissolved Hexavalent Chromium in Water by Ion Chromatography |
ASTM D 8026 : 2016 | Standard Practice for Determination of Tc-99 in Water by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) |
ASTM D 7284 : 2013 | Standard Test Method for Total Cyanide in Water by Micro Distillation followed by Flow Injection Analysis with Gas Diffusion Separation and Amperometric Detection |
ASTM D 6994 : 2015 : REDLINE | Standard Test Method for Determination of Metal Cyanide Complexes in Wastewater, Surface Water, Groundwater and Drinking Water Using Anion Exchange Chromatography with UV Detection |
ASTM D 5475 : 1993 : R2002 | Standard Test Method for Nitrogen- and Phosphorus-Containing Pesticides in Water by Gas Chromatography with a Nitrogen-Phosphorus Detector (Withdrawn 2011) |
ASTM D 1429 : 2013 : REDLINE | Standard Test Methods for Specific Gravity of Water and Brine |
ASTM D 3977 : 1997 : R2007 | Standard Test Methods for Determining Sediment Concentration in Water Samples |
ASTM D 5905 : 1998 : EDT 1 | Standard Practice for the Preparation of Substitute Wastewater |
ASTM D 2036 : 2009 : R2015 | Standard Test Methods for Cyanides in Water |
AASHTO T 291 : 1994 | METHOD OF TEST FOR DETERMINING WATER-SOLUBLE CHLORIDE ION CONTENT IN SOIL |
ASTM D 3082 : 2015 : REDLINE | Standard Test Method for Boron in Water |
ASTM D 5015 : 2015 : REDLINE | Standard Test Method for pH of Atmospheric Wet Deposition Samples by Electrometric Determination |
ASTM D 3865 : 2009 | Standard Test Method for Plutonium in Water |
ASTM D 4193:2008 | Standard Test Method for Thiocyanate in Water |
ASTM D 1067 : 2016 : REDLINE | Standard Test Methods for Acidity or Alkalinity of Water |
ASTM D 5907 : 2013-10 | TEST METHODS FOR FILTERABLE MATTER (TOTAL DISSOLVED SOLIDS) AND NONFILTERABLE MATTER (TOTAL SUSPENDED SOLIDS) IN WATER |
ASTM D 5089 : 1995 : R1999 | Standard Test Method for Velocity Measurements of Water in Open Channels with Electromagnetic Current Meters |
ASTM D 5905 : 1998 : R2013 | Standard Practice for the Preparation of Substitute Wastewater |
ASTM D 6698 : 2014 : REDLINE | Standard Test Method for On-Line Measurement of Turbidity Below 5 NTU in Water (Withdrawn 2023) |
ASTM D 5174 : 2007 | Standard Test Method for Trace Uranium in Water by Pulsed-Laser Phosphorimetry |
ASTM D 5412 : 1993 : R2017 : EDT 1 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
ASTM D 3697 : 2017 : REDLINE | Standard Test Method for Antimony in Water |
ASTM D 3972 : 2009 : R2015 | Standard Test Method for Isotopic Uranium in Water by Radiochemistry (Withdrawn 2024) |
ASTM D 8025 : 2016 | Standard Test Method for Determination of Select Pesticides in Water by Multiple Reaction Monitoring Liquid Chromatography Tandem Mass Spectrometry |
ASTM D 5904 : 2002 : R2009 | Standard Test Method for Total Carbon, Inorganic Carbon, and Organic Carbon in Water by Ultraviolet, Persulfate Oxidation, and Membrane Conductivity Detection |
ASTM D 5315 : 2004 : R2017 : EDT 1 | Standard Test Method for Determination of N-Methyl-Carbamoyloximes and N-Methylcarbamates in Water by Direct Aqueous Injection HPLC with Post-Column Derivatization |
ASTM D 5614 : 1994 : R2003 | Standard Test Method for Open Channel Flow Measurement of Water with Broad-Crested Weirs |
ASTM D 1941 : 1991 : R2001 | Standard Test Method for Open Channel Flow Measurement of Water with the Parshall Flume |
ASTM D 5613 : 1994 : R1998 | Standard Test Method for Open-Channel Measurement of Time of Travel Using Dye Tracers |
ASTM D 596 : 2001 : R2018 | Standard Guide for Reporting Results of Analysis of Water |
ASTM D 5462 : 2013 : REDLINE | Standard Test Method for On-Line Measurement of Low-Level Dissolved Oxygen in Water |
ASTM D 5412 : 1993 | TEST METHOD FOR QUANTIFICATION OF COMPLEX POLYCYCLIC AROMATIC HYDROCARBON MIXTURES OR PETROLEUM OILS IN WATER |
ASTM D 6239 : 2009 | Standard Test Method for Uranium in Drinking Water by High-Resolution Alpha-Liquid-Scintillation Spectrometry |
ASTM D 3977 : 1997 : R2013 | Standard Test Methods for Determining Sediment Concentration in Water Samples |
ASTM D 4785 : 2008 | Standard Test Method for Low-Level Analysis of Iodine Radioisotopes in Water |
ASTM D 1886 : 2014 : REDLINE | Standard Test Methods for Nickel in Water |
ASTM D 7598 : 2016 | Standard Test Method for Determination of Thiodiglycol in Water by Single Reaction Monitoring Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 5246 : 2015 | Standard Test Method for Isolation and Enumeration of <emph type="ital">Pseudomonas aeruginosa </emph> from Water |
ASTM D 5612 : 1994 : R2003 | Standard Guide for Quality Planning and Field Implementation of a Water Quality Measurement Program |
ASTM D 5243 : 1992 : R2007 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly at Culverts |
ASTM D 5790 : 1995 : R2012 | Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry |
ASTM D 5072 : 2009 : EDT 1 | Standard Test Method for Radon in Drinking Water |
ASTM D 4922 : 2009 | Standard Test Method for Determination of Radioactive Iron in Water |
ASTM D 5317 : 1998 : R2003 : EDT 1 | Standard Test Method for Determination of Chlorinated Organic Acid Compounds in Water by Gas Chromatography with an Electron Capture Detector |
ASTM D 3670 : 1991 : R2007 | Standard Guide for Determination of Precision and Bias of Methods of Committee D22 |
ASTM D 7742 : 2017 : REDLINE | Standard Practice for Determination of Nonylphenol Polyethoxylates (NPnEO, 3 ≤ n ≤ 18) and Octylphenol Polyethoxylates (OPnEO, 2 ≤ n ≤ 12) in Water by Single Reaction Monitoring (SRM) Liquid Chromatography/ Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 5612 : 1994 : R2013 | Standard Guide for Quality Planning and Field Implementation of a Water Quality Measurement Program |
ASTM D 4841 : 1988 : R1998 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
ASTM D 5812 : 1996 | Standard Test Method for Determination of Organochlorine Pesticides in Water by Capillary Column Gas Chromatography |
ASTM D 5997 : 2015 : REDLINE | Standard Test Method for On-Line Monitoring of Total Carbon, Inorganic Carbon in Water by Ultraviolet, Persulfate Oxidation, and Membrane Conductivity Detection |
ASTM D 1943 : 2005 | Standard Test Method for Alpha Particle Radioactivity of Water |
ASTM D 5905 : 1998 : R2003 | Standard Practice for the Preparation of Substitute Wastewater |
ASTM D 4841 : 1988 : R2013 : EDT 1 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
ASTM D 1293 : 2018 : REDLINE | Standard Test Methods for pH of Water |
ASTM D 4839 : 2003 : R2017 | Standard Test Method for Total Carbon and Organic Carbon in Water by Ultraviolet, or Persulfate Oxidation, or Both, and Infrared Detection |
ASTM D 4191 : 2015 : REDLINE | Standard Test Method for Sodium in Water by Atomic Absorption Spectrophotometry |
ASTM D 5673 : 2016 : REDLINE | Standard Test Method for Elements in Water by Inductively Coupled Plasma—Mass Spectrometry |
ASTM D 7295 : 2011-03 | PRACTICE FOR SAMPLING COMBUSTION EFFLUENTS AND OTHER STATIONARY SOURCES FOR THE SUBSEQUENT DETERMINATION OF HYDROGEN CYANIDE |
ASTM D 7598 : 2016 : R2017 | Standard Test Method for Determination of Thiodiglycol in Water by Single Reaction Monitoring Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 7535 : 2009 : EDT 1 | Standard Test Method for Lead-210 in Water |
ASTM D 5086 : 2001 : R2008 | Standard Test Method for Determination of Calcium, Magnesium, Potassium, and Sodium in Atmospheric Wet Deposition by Flame Atomic Absorption Spectrophotometry |
ASTM D 3372 : 2017 : REDLINE | Standard Test Method for Molybdenum in Water |
ASTM D 7574 : 2016 : REDLINE | Standard Test Method for Determination of Bisphenol A in Environmental Waters by Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 4841 : 1988 : R2003 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
ASTM D 4107 : 2008 | Standard Test Method for Tritium in Drinking Water |
ASTM D 3508 : 1978 : R1982 | METHOD FOR EVALUATING WATER TESTING MEMBRANE FILTERS FOR FAECAL COLIFORM RECOVERY |
ASTM D 5388 : 1993 : R2013 | Standard Test Method for Indirect Measurements of Discharge by Step-Backwater Method |
ASTM D 5089 : 1995 : R2003 | Standard Test Method for Velocity Measurements of Water in Open Channels with Electromagnetic Current Meters |
ASTM D 7573 : 2009 : R2017 | Standard Test Method for Total Carbon and Organic Carbon in Water by High Temperature Catalytic Combustion and Infrared Detection |
ASTM D 7066 : 2004 : EDT 1 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
ASTM D 7535 : 2009 | Standard Test Method for Lead-210 in Water |
ASTM D 2036 : 2009 | Standard Test Methods for Cyanides in Water |
ASTM D 3483 : 2014 : REDLINE | Standard Test Methods for Accumulated Deposition in a Steam Generator Tube |
ASTM D 5413 : 1993 : R2007 | Standard Test Methods for Measurement of Water Levels in Open-Water Bodies |
ASTM D 5242 : 1992 : R1996 | TEST METHOD FOR OPEN-CHANNEL FLOW MEASUREMENT OF WATER WITH THIN-PLATE WEIRS |
ASTM D 5389 : 1993 : R2013 | Standard Test Method for Open-Channel Flow Measurement by Acoustic Velocity Meter Systems |
ASTM D 1252 : 2006 | Standard Test Methods for Chemical Oxygen Demand (Dichromate Oxygen Demand) of Water |
ASTM D 5174 : 2007 : R2013 | Standard Test Method for Trace Uranium in Water by Pulsed-Laser Phosphorimetry (Withdrawn 2022) |
ASTM D 5317 : 1998 : R2017 | Standard Test Method for Determination of Chlorinated Organic Acid Compounds in Water by Gas Chromatography with an Electron Capture Detector |
ASTM D 6238 : 1998 : R2003 | Standard Test Method for Total Oxygen Demand in Water |
ASTM D 5173 : 2015 : REDLINE | Standard Guide for On-Line Monitoring of Total Organic Carbon in Water by Oxidation and Detection of Resulting Carbon Dioxide |
ASTM D 513 : 2016 : REDLINE | Standard Test Methods for Total and Dissolved Carbon Dioxide in Water |
ASTM D 3858 : 1995 : R2014 | Standard Test Method for Open-Channel Flow Measurement of Water by Velocity-Area Method (Withdrawn 2023) |
ASTM D 4793 : 2009 : R2017 | Standard Test Method for Sequential Batch Extraction of Waste with Water |
ASTM D 7510 : 2010 | Standard Practice for Performing Detection and Quantitation Estimation and Data Assessment Utilizing DQCALC Software, based on ASTM Practices D6091 and D6512 of Committee D19 on Water <a href="#fn00003"></a> |
ASTM D 1068 : 2015 : REDLINE | Standard Test Methods for Iron in Water |
ASTM E 800 : 2014 : REDLINE | Standard Guide for Measurement of Gases Present or Generated During Fires |
ASTM D 3861 : 1991 : R1998 | Standard Test Method for Quantity of Water-Extractable Matter in Membrane Filters |
ASTM D 596 : 2001 : R2011 | Standard Guide for Reporting Results of Analysis of Water |
ASTM D 5614 : 1994 : R2014 | Standard Test Method for Open Channel Flow Measurement of Water with Broad-Crested Weirs (Withdrawn 2023) |
ASTM D 5130 : 1995 : R2008 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method |
ASTM D 4192 : 2015 : REDLINE | Standard Test Method for Potassium in Water by Atomic Absorption Spectrophotometry |
ASTM D 1126 : 2017 : REDLINE | Standard Test Method for Hardness in Water |
ASTM D 4839 : 2003 | Standard Test Method for Total Carbon and Organic Carbon in Water by Ultraviolet, or Persulfate Oxidation, or Both, and Infrared Detection |
ASTM D 7315 : 2017 : REDLINE | Standard Test Method for Determination of Turbidity Above 1 Turbidity Unit (TU) in Static Mode |
ASTM D 4327 : 2017 : REDLINE | Standard Test Method for Anions in Water by Suppressed Ion Chromatography |
ASTM D 3867 : 2016 : REDLINE | Standard Test Methods for Nitrite-Nitrate in Water |
ASTM D 5085 : 2002 | Standard Test Method for Determination of Chloride, Nitrate, and Sulfate in Atmospheric Wet Deposition by Chemically Suppressed Ion Chromatography |
ASTM PS 74 : 1998 | Test Method for Oil and Grease (Solvent Extractable Substances) in Water by Gravimetric Determination (Withdrawn 2001) |
ASTM D 7599 : 2016 | Standard Test Method for Determination of Diethanolamine, Triethanolamine, <emph type="ital">N</emph>-Methyldiethanolamine and <emph type="ital">N</emph >-Ethyldiethanolamine in Water by Single Reaction Monitoring Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 8084 : 2017 | Standard Test Method for Photoelectrochemical Oxygen Demand of Freshwater Sources for Drinking Water Treatment Plants and Treated Drinking Water |
ASTM D 7937 : 2015 | Standard Test Method for In-situ Determination of Turbidity Above 1 Turbidity Unit (TU) in Surface Water |
ASTM D 5085 : 2002 : R2013 | Standard Test Method for Determination of Chloride, Nitrate, and Sulfate in Atmospheric Wet Deposition by Chemically Suppressed Ion Chromatography |
ASTM D 5544 : 2016 : REDLINE | Standard Test Method for On-Line Measurement of Residue After Evaporation of High-Purity Water |
ASTM D 5790 : 1995 | Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry |
ASTM D 6908 : 2006 | Standard Practice for Integrity Testing of Water Filtration Membrane Systems |
ASTM E 1625 : 1994 : R2001 | Standard Test Method for Determining Biodegradability of Organic Chemicals in Semi-Continuous Activated Sludge (SCAS) |
ASTM D 5129 : 1995 : R2003 | Standard Test Method for Open Channel Flow Measurement of Water Indirectly by Using Width Contractions |
ASTM D 1252 : 2006 : R2012 | Standard Test Methods for Chemical Oxygen Demand (Dichromate Oxygen Demand) of Water |
ASTM D 7066 : 2004 : R2011 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
ASTM D 5812 : 1996 : R2002 : EDT 1 | Standard Test Method for Determination of Organochlorine Pesticides in Water by Capillary Column Gas Chromatography (Withdrawn 2011) |
ASTM D 8018 : 2015 | Standard Test Method for Determination of (Tri-n-butyl)-n-tetradecylphosphonium chloride (TTPC) in Soil by Multiple Reaction Monitoring Liquid Chromatography/Mass Spectrometry (LC/MS/MS) |
ASTM D 6855 : 2017 : REDLINE | Standard Test Method for Determination of Turbidity Below 5 NTU in Static Mode |
ASTM D 6239 : 2009 : R2015 | Standard Test Method for Uranium in Drinking Water by High-Resolution Alpha-Liquid-Scintillation Spectrometry (Withdrawn 2024) |
ASTM D 5317 : 1998 | Standard Test Method for Determination of Chlorinated Organic Acid Compounds in Water by Gas Chromatography with an Electron Capture Detector |
ASTM D 7597 : 2016 : R2017 | Standard Test Method for Determination of Diisopropyl Methylphosphonate, Ethyl Hydrogen Dimethylamidophosphate, Ethyl Methylphosphonic Acid, Isopropyl Methylphosphonic Acid, Methylphosphonic Acid and Pinacolyl Methylphosphonic Acid in Water by Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 516 : 2016 : REDLINE | Standard Test Method for Sulfate Ion in Water |
ASTM D 857 : 2017 : REDLINE | Standard Test Method for Aluminum in Water |
ASTM D 7600 : 2016 | Standard Test Method for Determination of Aldicarb, Carbofuran, Oxamyl and Methomyl by Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 5613 : 1994 : R2003 | Standard Test Method for Open-Channel Measurement of Time of Travel Using Dye Tracers |
ASTM D 5130 : 1995 : R1999 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method |
ASTM E 1625 : 1994 | Standard Test Method for Determining Biodegradability of Organic Chemicals in Semi-Continuous Activated Sludge (SCAS) |
ASTM D 7066 : 2004 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
ASTM D 7485 : 2016 : REDLINE | Standard Test Method for Determination of Nonylphenol, p-<emph type="bdit">tert</emph >-Octylphenol, Nonylphenol Monoethoxylate and Nonylphenol Diethoxylate in Environmental Waters by Liquid Chromatography/Tandem Mass Spectrometry |
ASTM D 6508 : 2015 : REDLINE | Standard Test Method for Determination of Dissolved Inorganic Anions in Aqueous Matrices Using Capillary Ion Electrophoresis and Chromate Electrolyte |
ASTM D 7168 : 2016 : REDLINE | Standard Test Method for <sup>99</sup>Tc in Water by Solid Phase Extraction Disk |
ASTM D 1498 : 2014 : REDLINE | Standard Test Method for Oxidation-Reduction Potential of Water |
ASTM D 3649 : 2006 | Standard Practice for High-Resolution Gamma-Ray Spectrometry of Water |
ASTM D 5242 : 1992 : R2001 | Standard Test Method for Open-Channel Flow Measurement of Water with Thin-Plate Weirs |
ASTM D 1941 : 1991 : R2013 | Standard Test Method for Open Channel Flow Measurement of Water with the Parshall Flume |
ASTM D 3859 : 2016-02 | TEST METHODS FOR SELENIUM IN WATER |
ASTM D 7535 : 2009 : R2015 | Standard Test Method for Lead-210 in Water (Withdrawn 2024) |
NACE TM 03 99 : 2005 | Standard Test Method for Phosphonate in Brine |
ASTM D 4785 : 2008 : R2013 : EDT 1 | Standard Test Method for Low-Level Analysis of Iodine Radioisotopes in Water |
ASTM D 7126 : 2015 : REDLINE | Standard Test Method for On-Line Colorimetric Measurement of Silica |
ASTM D 8001 : 2016 : EDT 1 | Standard Test Method for Determination of Total Nitrogen, Total Kjeldahl Nitrogen by Calculation, and Total Phosphorus in Water, Wastewater by Ion Chromatography |
ASTM D 5315 : 2004 | Standard Test Method for Determination of N-Methyl-Carbamoyloximes and N-Methylcarbamates in Water by Direct Aqueous Injection HPLC with Post-Column Derivatization |
ASTM D 5243 : 1992 : R2013 | Standard Test Method for Open-Channel Flow Measurement of Water Indirectly at Culverts |
ASTM D 3858 : 1995 : R2003 | Standard Test Method for Open-Channel Flow Measurement of Water by Velocity-Area Method |
ASTM D 5614 : 1994 : R1998 | Standard Test Method for Open Channel Flow Measurement of Water with Broad-Crested Weirs |
ASTM D 5612 : 1994 : R1998 | Standard Guide for Quality Planning and Field Implementation of a Water Quality Measurement Program |
ASTM D 3861 : 1991 : R2003 | Standard Test Method for Quantity of Water-Extractable Matter in Membrane Filters |
ASTM D 1426 : 2015 : REDLINE | Standard Test Methods for Ammonia Nitrogen In Water |
ASTM D 1179 : 2016 : REDLINE | Standard Test Methods for Fluoride Ion in Water |
ASTM D 6303 : 1998 | Standard Test Method for Formaldehyde in Water (Withdrawn 2007) |
ASTM D 596 : 2001 : R2006 | Standard Guide for Reporting Results of Analysis of Water |
ASTM D 1976:2013-07 | TEST METHOD FOR ELEMENTS IN WATER BY INDUCTIVELY-COUPLED ARGON PLASMA ATOMIC EMISSION SPECTROSCOPY |
ASTM D 7510 : 2010 : R2016 : EDT 1 | Standard Practice for Performing Detection and Quantitation Estimation and Data Assessment Utilizing DQCALC Software, based on ASTM Practices D6091 and D6512 of Committee D19 on Water |
ASTM D 1890 : 2015 : R2017 | Standard Test Method for Beta Particle Radioactivity of Water |
ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
ASTM D 5847 : 2002 : R2012 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
ASTM D 5086 : 2001 : R2013 | Standard Test Method for Determination of Calcium, Magnesium, Potassium, and Sodium in Atmospheric Wet Deposition by Flame Atomic Absorption Spectrophotometry |
ASTM D 1941 : 1991 : R1996 | Standard Test Method for Open Channel Flow Measurement of Water with the Parshall Flume |
ASTM D 4409 : 1995 : R2014 | Standard Test Method for Velocity Measurements of Water in Open Channels with Rotating Element Current Meters (Withdrawn 2023) |
ASTM D 2187 : 2017 : REDLINE | Standard Test Methods and Practices for Evaluating Physical and Chemical Properties of Particulate Ion-Exchange Resins |
ASTM D 6919 : 2017 : REDLINE | Standard Test Method for Determination of Dissolved Alkali and Alkaline Earth Cations and Ammonium in Water and Wastewater by Ion Chromatography |
ASTM D 3670 : 1991 : R2014 | Standard Guide for Determination of Precision and Bias of Methods of Committee D22 |
ASTM D 3921 : 1996 : R2003 : EDT 1 | Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water |
ASTM D 3651 : 2016 : REDLINE | Standard Test Method for Barium in Brackish Water, Seawater, and Brines |
ASTM D 7731 : 2017 : REDLINE | Standard Test Method for Determination of Dipropylene Glycol Monobutyl Ether and Ethylene Glycol Monobutyl Ether in Sea Water by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS) |
ASTM D 1688 : 2017 : REDLINE | Standard Test Methods for Copper in Water |
ASTM D 2460 : 2007 : R2013 | Standard Test Method for Alpha-Particle-Emitting Isotopes of Radium in Water (Withdrawn 2022) |
ASTM D 3861 : 1991 : R2011 | Standard Test Method for Quantity of Water-Extractable Matter in Membrane Filters (Withdrawn 2020) |
ASTM D 5996 : 2016 : REDLINE | Standard Test Method for Measuring Anionic Contaminants in High-Purity Water by On-Line Ion Chromatography |
ASTM D 5284 : 2009 : R2017 | Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid |
ASTM D 3558 : 2015 : REDLINE | Standard Test Methods for Cobalt in Water |
ASTM D 4107 : 2008 : R2013 | Standard Test Method for Tritium in Drinking Water |
ASTM D 5916 : 1996 | Standard Test Method for Detection and Enumeration of <i>Clostridium perfringens</i> from Water and Extracted Sediments by Membrane Filtration (MF) |
ASTM D 5389 : 1993 | TEST METHOD FOR OPEN-CHANNEL FLOW MEASUREMENT BY ACOUSTIC VELOCITY METER SYSTEMS |
ASTM D 6807 : 2017 : REDLINE | Standard Test Method for Operating Performance of Continuous Electrodeionization Systems on Reverse Osmosis Permeates from<brk/>2 to 100 μS/cm |
ASTM D 596 : 2001 | Standard Guide for Reporting Results of Analysis of Water |
ASTM D 4517 : 2015 : REDLINE | Standard Test Method for Low-Level Total Silica in High-Purity Water by Flameless Atomic Absorption Spectroscopy |
ASTM D 5315 : 2004 : R2011 | Standard Test Method for Determination of N-Methyl-Carbamoyloximes and N-Methylcarbamates in Water by Direct Aqueous Injection HPLC with Post-Column Derivatization |
ASTM D 5904 : 2002 : R2017 | Standard Test Method for Total Carbon, Inorganic Carbon, and Organic Carbon in Water by Ultraviolet, Persulfate Oxidation, and Membrane Conductivity Detection |
ASTM D 4456 : 2017 : REDLINE | Standard Test Methods for Physical and Chemical Properties of Powdered Ion Exchange Resins |
ASTM D 6238 : 1998 | Standard Test Method for Total Oxygen Demand in Water |
ASTM D 6091 : 2007 : R2014 | Standard Practice for 99 %/95 % Interlaboratory Detection Estimate (IDE) for Analytical Methods with Negligible Calibration Error (Withdrawn 2023) |
ASTM D 5847 : 2002 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
ASTM D 5389 : 1993 : R1997 | Standard Test Method for Open-Channel Flow Measurement by Acoustic Velocity Meter Systems |
ASTM F 60 : 1968 : R1983 | Methods for Detection and Enumeration of Microbiological Contaminants in Water Used for Processing Electron and Microelectronic Devices (Withdrawn 1991) |
ASTM D 5389 : 1993 : R2007 | Standard Test Method for Open-Channel Flow Measurement by Acoustic Velocity Meter Systems |
ASTM D 3875 : 2015 : REDLINE | Standard Test Method for Alkalinity in Brackish Water, Seawater, and Brines |
ASTM D 5128 : 2014 : REDLINE | Standard Test Method for On-Line pH Measurement of Water of Low Conductivity |
ASTM D 5072 : 2009 | Standard Test Method for Radon in Drinking Water |
ASTM D 4658 : 2015 : REDLINE | Standard Test Method for Sulfide Ion in Water |
ASTM D 5790 : 1995 : R2006 | Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry |
ASTM D 7725 : 2017 : REDLINE | Standard Test Method for the Continuous Measurement of Turbidity Above 1 Turbidity Unit (TU) |
ASTM D 4409 : 1995 : R2008 | Standard Test Method for Velocity Measurements of Water in Open Channels with Rotating Element Current Meters |
ASTM D 3591 : 2017 : REDLINE | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
ASTM D 1129 : 2013 : REDLINE | Standard Terminology Relating to Water |
ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM D 5905 : 1998 : R2018 | Standard Practice for the Preparation of Substitute Wastewater |
ASTM D 1141 : 1998 : EDT 1 | Standard Practice for the Preparation of Substitute Ocean Water |
ASTM D 5790 : 1995 | Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.