ASTM D 2673 : 2014 : R2022
Current
The latest, up-to-date edition.
Standard Specification for Oriented Polypropylene Film
Hardcopy , PDF
English
18-03-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers oriented polypropylene (OPP) film in the thickness range from 10 to 75 μm (0.4 to 3.0 mils).
1.2The film can contain colorants, stabilizers, or other additives, and can be coated for the improvement of performance properties (heat sealability, gas permeability, and so forth).
1.3The film can be annealed (heat-set) to reduce the unrestrained linear shrinkage and shrink tension on exposure to heat.
1.4The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.5The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 96/E96M : 2022 : REV A : EDT 1 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2022 : REV A | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 1746 : 2023 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 1922 : 2023 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM E 96/E96M : 2022 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM F 88/F88M : 2023 | Standard Test Method for Seal Strength of Flexible Barrier Materials |
| ASTM D 2578 : 2017 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM E 96/E96M : 2023 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2024 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
| ASTM D 3985 : 2024 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 1922 : 2015 : R2020 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1434 : 1982 : R2015 : EDT 1 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
| ASTM D 4321 : 2024 | Standard Test Method for Package Yield of Plastic Film |
| ASTM D 4101 : 2024 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1746 : 2015 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 2578 : 2023 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 1434 : 2023 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
| ASTM F 88/F88M : 2021 | Standard Test Method for Seal Strength of Flexible Barrier Materials |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3985 : 2017 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4321 : 2015 | Standard Test Method for Package Yield of Plastic Film (Withdrawn 2024) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.