ASTM D 2513 : 2018 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
Hardcopy , PDF
07-09-2020
English
31-08-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the transmission and distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are also covered.
1.1.1This specification does not cover threaded pipe. Design considerations are discussed in Appendix X1. In-plant quality control programs are specified in Annex A1 and Annex A2.
1.1.2See Specification F2619/F2619M for polyethylene piping for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.
1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4The following is an index of the annexes and appendix in this specification:
| Annex | Subject |
| Annex A1 | In-Plant Quality Control for all materials up to 12 in. |
| Annex A2 | In-Plant Quality Control for PE materials 14 in. and larger. |
| Appendixes | Subject |
| Appendix X1 | Design Consideration |
1.5The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 1041 : 2002 : R2016 | Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing |
| ASTM F 1563 : 2001 : R2011 | Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing |
| ASTM F 1588 : 1996 : R2015 | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM F 1804 : 2008 : R2016 | Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation |
| ASTM F 2818 : 2010 : R2014 : EDT 1 | Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing |
| ASTM F 2830 : 2011 : R2017 | Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer (Withdrawn 2024) |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM F 905 : 2004 : R2018 | Standard Practice for Qualification of Polyethylene Saddle-Fused Joints |
| ASTM F 1055 : 2016 : REV A | Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing |
| ASTM F 2897 : 2015 : REV A | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2620 : 2019 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 1734 : 2019 | Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe |
| ASTM F 1924 : 2019 | Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing |
| ASTM F 2509 : 2015 : R2019 | Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing |
| ASTM F 2206 : 2019 | Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE) |
| ASTM F 2619/F2619M : 2013 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM D 2683 : 2014 | Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing |
| ASTM F 1056 : 2018 | Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings |
| ASTM D 3261 : 2016 | Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing |
| ASTM F 1962 : 2011 | Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings (Withdrawn 2020) |
| ASTM F 2634 : 2015 | Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method |
| ASTM F 2880 : 2014 | Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in. |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 2897 : 2011 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2290 : 2016 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 1563 : 1994 : R2000 | Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing |
| ASTM F 1473 : 2018 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM D 3261 : 2015 | Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing |
| ASTM F 2138 : 2012 : R2017 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM D 2837 : 1998 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 1435 : 1994 | Standard Practice for Outdoor Weathering of Plastics |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1898 : 1968 : R1989 | Standard Practice for Sampling of Plastics (Withdrawn 1998) |
| ASTM D 2290 : 2000 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method |
| ASTM F 2620 : 2006 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 1055 : 2015 | Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2565 : 1970 | Standard Recommended Practice For Operating Xenon Arc-Type (Water-Cooled) Light - And Water-Exposure Apparatus For Exposure Of Plastics |
| ASTM F 2897 : 2015 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1473 : 2016 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM D 3261 : 1997 | Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.