ASTM D 217 : 2021 : REV A
Current
The latest, up-to-date edition.
Standard Test Methods for Cone Penetration of Lubricating Grease
Hardcopy , PDF
English
20-12-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
14
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover four procedures for measuring the consistency of lubricating greases by the penetration of a cone of specified dimensions, mass, and finish. The penetration is measured in tenths of a millimetre.
Note 1:The National Lubricating Grease Institute (NLGI)3 classified greases according to their consistency as measured by the worked penetration. The classification system is as follows: NLGI Worked Penetration Range, 000 445 to 475 00 400 to 430 0 355 to 385 1 310 to 340 2 265 to 295 3 220 to 250 4 175 to 205 5 130 to 160 6 85 to 115
Consistency Number
25 °C (77 °F)
1.1.1The procedures for unworked, worked, and prolonged worked penetration are applicable to greases having penetrations between 85 and 475, that is, to greases with consistency numbers between NLGI 6 and NLGI 000. An undisturbed penetration test, described in Appendix X1, is similar to the unworked penetration test.
1.1.2The block penetration procedure is applicable to greases that are sufficiently hard to hold their shape. Such greases usually have penetrations below eighty-five tenths of a millimetre.
1.1.3Unworked penetrations do not generally represent the consistency of greases in use as effectively as do worked penetrations. The latter are usually preferred for inspecting lubricating greases.
1.2None of the four procedures is considered suitable for the measurement of the consistency of petrolatums by penetration. Test Method D937 should be used for such products.
1.3The dimensions of the equipment described in these test methods are given in SI units as the primary unit of measure with equivalent imperial units as accetpable alternatives where applicable. In cases where equivalent SI conversions are not known, notes are added for clarification. Temperatures and other dimensions are given in the preferred SI units; the values shown in parentheses are provided for information.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7421 : 2019 | Standard Test Method for Determining Extreme Pressure Properties of Lubricating Oils Using High-Frequency, Linear-Oscillation (SRV) Test Machine |
| ASTM D 4425 : 2019 | Standard Test Method for Oil Separation from Lubricating Grease by Centrifuging (Koppers Method) |
| ASTM D 5078/D5078M : 2011 : R2021 | Standard Specification for Crack Filler, Hot-Applied, for Asphalt Concrete and Portland Cement Concrete Pavements |
| ASTM D 4289 : 2019 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM F 2489 : 2006 : R2013 | Standard Guide for Instrument and Precision Bearing Lubricants—Part 2 Greases |
| ASTM C 877 : 2021 | Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections |
| ASTM D 8324 : 2021 | Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit |
| ASTM D 6185 : 2011 : R2017 | Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases |
| ASTM D 8022 : 2020 | Standard Test Method for Roll Stability of Lubricating Grease in Presence of Water (Wet Roll Stability Test) |
| ASTM G 63 : 2015 | Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service |
| ASTM D 5706 : 2016 | Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using a High-Frequency, Linear-Oscillation (SRV) Test Machine |
| ASTM D 4049 : 2020 | Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray |
| ASTM D 7918 : 2017 : REV A | Standard Test Method for Measurement of Flow Properties and Evaluation of Wear, Contaminants, and Oxidative Properties of Lubricating Grease by Die Extrusion Method and Preparation |
| ASTM D 1321 : 2016 : REV A | Standard Test Method for Needle Penetration of Petroleum Waxes |
| ASTM C 990 : 2009 : R2019 | Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants |
| ASTM D 2595 : 2017 | Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range |
| ASTM D 5707 : 2019 | Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine |
| ASTM D 7718 : 2011 : R2019 | Standard Practice for Obtaining In-Service Samples of Lubricating Grease |
| ASTM D 937 : 2007 : R2019 | Standard Test Method for Cone Penetration of Petrolatum |
| ASTM D 566 : 2020 | Standard Test Method for Dropping Point of Lubricating Grease (Withdrawn 2023) |
| ASTM D 4950 : 2019 | Standard Classification and Specification for Automotive Service Greases |
| ASTM D 4732 : 2013 : R2020 | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM C 782 : 2013 : R2018 | Standard Test Method for Softness of Preformed Tape Sealants |
| ASTM D 2265 : 2020 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 4693 : 2007 : R2021 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM D 6297 : 2020 | Standard Specification for Asphaltic Plug Joints for Bridges |
| ASTM D 7594 : 2019 | Standard Test Method for Determining Fretting Wear Resistance of Lubricating Greases Under High Hertzian Contact Pressures Using a High-Frequency, Linear-Oscillation (SRV) Test Machine |
| ASTM D 7420 : 2018 | Standard Test Method for Determining Tribomechanical Properties of Grease Lubricated Plastic Socket Suspension Joints Using a High-Frequency, Linear-Oscillation (SRV) Test Machine |
| ASTM C 990M : 2009 : R2019 | Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric) (Withdrawn 2024) |
| ASTM D 1403 : 2020 : REV B | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 128 : 1998 : R2019 | Standard Test Methods for Analysis of Lubricating Grease |
| ASTM D 7342 : 2020 | Standard Test Method for Prolonged Worked Stability of Lubricating Grease in Presence of Water (Water Stability Test) |
| ASTM D 1092 : 2020 | Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases |
| ASTM D 1831 : 2020 | Standard Test Method for Roll Stability of Lubricating Grease |
| ASTM D 972 : 2016 | Standard Test Method for Evaporation Loss of Lubricating Greases and Oils |
| ASTM D 3757 : 2016 | Standard Guide for Preparing Specifications for Solvent-based Floor Polishes |
| ASTM C 877M : 2021 | Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections (Metric) |
| ASTM D 6184 : 2017 | Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method) |
| ASTM D 5329 : 2020 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
| ASTM D 4175 : 2022 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2022 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2023 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2022 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2023 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2023 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2022 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2024 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.