ASTM D 2069 : 1991 : R1998
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Standard Specification for Marine Fuels (Withdrawn 2003)
Hardcopy , PDF
05-11-2013
English
10-04-1998
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL 05.01, 2001 Specifies the required properties at the time and place of custody transfer for petroleum fuels for marine use in boilers and diesel engines.
| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Withdrawn
|
1.1 This specification specifies the required properties at the time and place of custody transfer for petroleum fuels for marine use in diesel engines and boilers. It is for the guidance of interested parties such as marine equipment designers, and suppliers and purchasers of marine fuels.
1.2 This specification excludes marine fuels intended for gas turbine use. Gas turbine fuels for non-aviation use are covered by Specification
1.3 This specification does not imply the availability of all categories of fuel at all ports.
1.4 This specification shall not preclude observance of national or local regulations that may be more restrictive.
Note 1-This specification takes into account the international requirements for flash point as stated in the International Maritime Organization (IMO) Convention for Safety of Life at Sea (SOLAS) 1974, Amendment 1, Chapter II-2, Regulation 15.1.5 The values stated in SI units are to be regarded as standard. The values stated in inch-pound units are for information only.
1.6 The following precautionary statement pertains to the test method portion only, Section 6, of this specification. This standard does not purport to address the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.>
| ASTM D 6258 : 2017 : REDLINE | Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels |
| ASTM D 6748 : 2002 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM D 7687 : 2017 : REDLINE | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 6748 : 2002 : REV A : R2012 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM D 6217 : 2011 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration |
| ASTM D 6748 : 2002 : REV A | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM D 7464 : 2014 : REDLINE | Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing |
| ASTM D 6748 : 2002 : REV A : R2007 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) <a href="#fn00002"></a> |
| ASTM E 1259 : 2018 | Standard Practice for Evaluation of Antimicrobials in Liquid Fuels Boiling Below 390 °C |
| ASTM D 6748 : 2002 : REV A : R2017 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM D 6217 : 2018 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration |
| ASTM D 7464 : 2014 | Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing |
| ASTM D 7687 : 2017 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 6469 : 2017 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 6258 : 2017 | Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels |
| ASTM D 6469 : 2017 : REDLINE | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 6217 : 2011 : R2016 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration |
| ASTM D 189 : 2006 : EDT 1 | Standard Test Method for Conradson Carbon Residue of Petroleum Products |
| ASTM D 524 : 2015 : REDLINE | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.