ASTM D 2042 : 2022
Current
The latest, up-to-date edition.
Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene or Toluene
Hardcopy , PDF
English
09-02-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 04
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the determination of the degree of solubility in trichloroethylene or toluene of asphalt materials having little or no mineral matter.
Note 1:This method is not applicable to tars and their distillation residues or highly cracked petroleum products. For methods covering tars, pitches, and other highly cracked petroleum products, and the use of other solvents, see Test Methods D4, D2318, and D2764.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precaution statements are given in Section 7.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8125 : 2018 | Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE) |
| ASTM D 244 : 2009 : R2017 | Standard Test Methods and Practices for Emulsified Asphalts |
| ASTM D 3381/D3381M : 2018 | Standard Specification for Viscosity-Graded Asphalt Binder for Use in Pavement Construction |
| ASTM D 2027/D2027M : 2019 | Standard Specification for Cutback Asphalt (Medium-Curing Type) |
| ASTM D 977 : 2020 | Standard Specification for Emulsified Asphalt |
| ASTM D 2397/D2397M : 2020 | Standard Specification for Cationic Emulsified Asphalt |
| ASTM D 946/D946M : 2020 | Standard Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction |
| ASTM D 7654/D7654M : 2010 : R2018 | Standard Specification for Asphalt Used in Roofing Measured by Dynamic Shear Rheometer |
| ASTM D 6152/D6152M : 2012 : R2018 | Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing |
| ASTM D 5505 : 2014 : R2020 | Standard Practice for Classifying Emulsified Recycling Agents |
| ASTM D 449/D449M : 2003 : R2021 | Standard Specification for Asphalt Used in Dampproofing and Waterproofing |
| ASTM D 2521/D2521M : 1976 : R2021 | Standard Specification for Asphalt Used in Canal, Ditch, and Pond Lining |
| ASTM A 849 : 2015 : R2021 | Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe |
| ASTM D 7553 : 2015 : R2021 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
| ASTM D 6373 : 2021 : REV A | Standard Specification for Performance-Graded Asphalt Binder |
| ASTM D 8239 : 2021 : REV A | Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test |
| ASTM D 3141/D3141M : 2021 | Standard Specification for Asphalt for Undersealing Portland-Cement Concrete Pavements |
| ASTM D 2028/D2028M : 2015 : R2021 : EDT 1 | Standard Specification for Cutback Asphalt (Rapid-Curing Type) |
| ASTM D 6154 : 2015 : R2021 : EDT 1 | Standard Specification for Chemically Modified Asphalt Cement for Use in Pavement Construction |
| ASTM D 2026/D2026M : 2015 : R2021 : EDT 1 | Standard Specification for Cutback Asphalt (Slow-Curing Type) |
| ASTM D 312/D312M : 2016 : REV A | Standard Specification for Asphalt Used in Roofing |
| ASTM D 8051/D8051M : 2016 | Standard Specification for Wax-Modified Asphalt Used in Roofing |
| ASTM D 4753 : 2015 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
| ASTM D 4753 : 2024 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
| ASTM D 4 : 1986 : R2024 | Standard Test Method for Bitumen Content |
| ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2024 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 4 : 1986 : R2018 | Standard Test Method for Bitumen Content |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.