ASTM D 1693 : 2007
NA
Status of Standard is Unknown
Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
Hardcopy , PDF
English
01-03-2007
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
NA
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers the determination of the susceptibility of ethylene plastics, as defined in Terminology D 883, to environmental stress-cracking when subjected to the conditions herein specified. Under certain conditions of stress and in the presence of environments such as soaps, wetting agents, oils, or detergents, ethylene plastics may exhibit mechanical failure by cracking.
1.2 The values stated in SI units are to be regarded as standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no similar or equivalent ISO standard.| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7082 : 2015 | Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe |
| ASTM D 2308 : 2007 : R2013 | Standard Specification for Thermoplastic Polyethylene Jacket for Electrical Wire and Cable |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4565 : 2015 | Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable |
| ASTM D 1998 : 2015 | Standard Specification for Polyethylene Upright Storage Tanks |
| ASTM F 810 : 2012 : R2018 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM F 2718 : 2009 : R2015 | Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022) |
| ASTM D 3554 : 2007 : R2018 | Standard Specification for Track-Resistant Black Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation |
| ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM D 7436 : 2017 | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.