ASTM D 1613 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products
Hardcopy , PDF
11-11-2014
English
01-04-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
3
|
| ProductNote |
Reconfirmed 2006
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers the determination of total acidity as acetic acid, in concentrations below 0.05 %, in organic compounds and hydrocarbon mixtures used in paint, varnish, and lacquer solvents and diluents. It is known to be applicable to such mixtures as low molecular weight saturated and unsaturated alcohols, ketones, ethers, esters, hydrocarbon diluents, naphtha, and other light distillate petroleum fractions.
1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 For specific hazard information and guidance consult supplier's Material Safety Data Sheet.
This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 3728 : 2008 : R2012 | Standard Specification for 2-Ethoxyethyl Acetate (99 % Grade) (Withdrawn 2021) |
| ASTM D 7862 : 2019 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
| ASTM D 7713 : 2018 | Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal) |
| ASTM D 4806 : 2019 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
| ASTM D 3329 : 2003 : R2017 | Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography |
| ASTM D 1718 : 2009 : R2017 | Standard Specification for Isobutyl Acetate (95 % Grade) |
| ASTM D 608 : 2005 : R2019 | Standard Specification for Dibutyl Phthalate |
| ASTM D 4836 : 2009 : R2017 | Standard Specification for Dipropylene Glycol Monomethyl Ether |
| ASTM D 4835 : 2008 : R2012 | Standard Specification for Propylene Glycol Monomethyl Ether Acetate (Withdrawn 2021) |
| ASTM D 4709 : 2007 : R2012 | Standard Specification for Methyl Acrylate (Withdrawn 2021) |
| ASTM D 2627 : 2008 : R2012 | Standard Specification for Diacetone Alcohol (Withdrawn 2021) |
| ASTM D 2636 : 2007 : R2012 | Standard Specification for Hexylene Glycol (Withdrawn 2021) |
| ASTM D 2916 : 2009 : R2017 | Standard Specification for Isophorone |
| ASTM D 3540 : 2012 | Standard Specification for Primary Amyl Acetate, Synthetic (98 % Grade) (Withdrawn 2021) |
| ASTM D 4615 : 2012 | Standard Specification for n-Butyl Acetate (All Grades) (Withdrawn 2021) |
| ASTM D 5008 : 2007 : R2012 | Standard Test Method for Ethyl Methyl Pentanol Content and Purity Value of 2-Ethylhexanol By Gas Chromatography (Withdrawn 2021) |
| ASTM D 2804 : 2002 : R2012 | Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography (Withdrawn 2021) |
| ASTM D 268 : 2001 : R2012 | Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material (Withdrawn 2021) |
| ASTM D 4252 : 1989 : R2017 | Standard Test Methods for Chemical Analysis of Alcohol Ethoxylates and Alkylphenol Ethoxylates |
| ASTM D 4837 : 2007 : R2012 | Standard Specification for Propylene Glycol Monomethyl Ether (Withdrawn 2021) |
| ASTM D 2635 : 2007 : R2012 | Standard Specification for Methyl Isobutyl Carbinol (Withdrawn 2021) |
| ASTM D 3131 : 2007 : R2013 | Standard Specification for Isopropyl Acetate (99 % Grade) |
| ASTM D 329 : 2007 : R2013 | Standard Specification for Acetone |
| ASTM D 4171 : 2016 : REV A | Standard Specification for Fuel System Icing Inhibitors |
| ASTM D 7388 : 2018 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
| ASTM E 1177 : 2014 | Standard Specification for Engine Coolant Grade Glycol |
| ASTM D 1153 : 2012 | Standard Specification for Methyl Isobutyl Ketone (Withdrawn 2021) |
| ASTM D 3545 : 2006 : R2012 | Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography (Withdrawn 2021) |
| ASTM D 5797 : 2018 | Standard Specification for Methanol Fuel Blends (M51–M85) for Methanol-Capable Automotive Spark-Ignition Engines |
| ASTM D 3548 : 2009 : R2017 | Standard Specification for Ethyl Acrylate |
| ASTM D 4773 : 2002 : R2012 | Standard Test Method for Purity of Propylene Glycol Monomethyl Ether, Dipropylene Glycol Monomethyl Ether, and Propylene Glycol Monomethyl Ether Acetate (Withdrawn 2021) |
| ASTM D 3585 : 2008 : R2013 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 3128 : 2007 : R2013 | Standard Specification for 2-Methoxyethanol |
| ASTM D 330 : 2007 : R2013 | Standard Specification for 2-Butoxyethanol |
| ASTM D 3893 : 2003 : R2017 | Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography |
| ASTM D 2634 : 2007 : R2013 | Standard Specification for Methyl Amyl Acetate (95 % Grade) |
| ASTM D 5137 : 2007 : R2013 | Standard Specification for Hexyl Acetate |
| ASTM D 2917 : 2007 : R2013 | Standard Specification for Methyl Isoamyl Ketone |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.