ASTM D 1603 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Carbon Black Content in Olefin Plastics
Hardcopy , PDF
11-11-2014
English
01-09-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers the determination of the carbon black content in polyethylene, polypropylene, and polybutylene plastics. Its use with acrylic or other polar monomer modifications which might affect the accuracy is not recommended. Determinations of carbon black content are made gravimetrically after pyrolysis of the sample under nitrogen. This test method is not applicable to compositions that contain nonvolatile pigments or fillers other than carbon black.
1.1.1 This test method is not applicable to materials containing brominated flame retardant additives at the end.
1.2 The values stated in SI units are to be regarded as standard. The values in parentheses are given for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1—This standard and ISO 6964-1986(E) address the same subject matter, but differ in technical content.
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 2619/F2619M : 2013 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM D 4218 : 2015 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
| ASTM F 2807 : 2013 : R2018 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024) |
| ASTM F 3203 : 2018 | Standard Test Method for Determination of Gel Content of Crosslinked Polyethylene (PEX) Pipes and Tubing |
| ASTM F 3123 : 2018 : REV A | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM F 2905/F2905M : 2013 | Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications |
| ASTM F 2968/F2968M : 2014 : REV A | Standard Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas Distribution Applications |
| ASTM F 3034 : 2015 | Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE) |
| ASTM D 7273/D7273M : 2008 : R2013 : EDT 1 | Standard Guide for for Acceptance Testing Requirements for Geonets and Geonet Drainage Geocomposites |
| ASTM D 2737 : 2012 : REV A | Standard Specification for Polyethylene (PE) Plastic Tubing |
| ASTM D 2239 : 2012 : REV A | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
| ASTM F 2947/F2947M : 2019 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM D 2765 : 2016 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.