ASTM D 1217 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer
13-06-2020
English
01-12-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.01, 2016 Defines the measurement of the density of pure hydrocarbons or petroleum distillates boiling between 90 degrees C and 110 degrees C that can be handled in a normal fashion as a liquid at the specified test temperatures of 20 degrees C and 25 degrees C.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the measurement of the density of pure hydrocarbons or petroleum distillates boiling between 90 °C and 110 °C that can be handled in a normal fashion as a liquid at the specified test temperatures of 20 °C and 25 °C.
1.2This test method provides a calculation procedure for the conversion of density to relative density (specific gravity).
1.3WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products in your state or country may be prohibited by law.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 7.
| ASTM B 963 : 2017 : REDLINE | Standard Test Methods for Oil Content, Oil-Impregnation Efficiency, and Surface-Connected Porosity of Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle |
| ASTM E 201 : 1996 | Test Method for Calculation of Volume and Weight of Industrial Chemical Liquids (Withdrawn 2001) |
| ASTM D 2892 : 2017-05 | TEST METHOD FOR DISTILLATION OF CRUDE PETROLEUM (15-THEORETICAL PLATE COLUMN) |
| ASTM D 1555M : 2016 : REDLINE | Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane [Metric] |
| ASTM D 1555 : 2016 : REDLINE | Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane |
| ASTM D 6448 : 2016 : REDLINE | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM C 729 : 2011 : R2016 | Standard Test Method for Density of Glass by the Sink-Float Comparator |
| ISO 9940:2015 | Aerospace series Fluid, hydraulic, phosphate ester-base, fire resistant Technical specification |
| ASTM D 4529 : 2017 : REDLINE | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 1481 : 2017 : REDLINE | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Lipkin Bicapillary Pycnometer |
| ASTM D 2994 : 1998 | Standard Test Methods for Rubberized Tar (Withdrawn 2000) |
| 12/30234431 DC : 0 | BS ISO 9940 - AEROSPACE - FIRE RESISTANT HYDRAULIC FLUIDS |
| API MPMS CH9.4 : 2018 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 9.4 - CONTINUOUS DENSITY MEASUREMENT UNDER DYNAMIC (FLOWING) CONDITIONS |
| ASTM C 729 : 2011 | Standard Test Method for Density of Glass by the Sink-Float Comparator |
| ASTM D 5002 : 2016-02 | TEST METHOD FOR DENSITY AND RELATIVE DENSITY OF CRUDE OILS BY DIGITAL DENSITY ANALYZER |
| SAE AS 1241 : 2016 | FIRE RESISTANT PHOSPHATE ESTER HYDRAULIC FLUID FOR AIRCRAFT |
| ASTM D 2766 : 1995 : R2009 | Standard Test Method for Specific Heat of Liquids and Solids (Withdrawn 2018) |
| ASTM D 5236 : 2017-05 | TEST METHOD FOR DISTILLATION OF HEAVY HYDROCARBON MIXTURES (VACUUM POTSTILL METHOD) |
| BS ISO 9940:2015 | Aerospace series. Fluid, hydraulic, phosphate ester-base, fire resistant. Technical specification |
| ASTM D 1480 : 2015 : REDLINE | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer |
| MIL-T-63466 Base Document:1981 | THIONYL CHLORIDE (FOR USE IN AMMUNITION) |
| ASTM D 2766 : 1995 : R2005 | Standard Test Method for Specific Heat of Liquids and Solids |
| 13/30290460 DC : 0 | BS ISO 9940 - AEROSPACE SERIES - FLUID, HYDRAULIC, PHOSPHATE ESTER-BASE, FIRE RESISTANT - TECHNICAL SPECIFICATION |
| 14/30302298 DC : 0 | BS ISO 9940 - AEROSPACE SERIES - FLUID, HYDRAULIC, PHOSPHATE ESTER-BASE, FIRE RESISTANT - TECHNICAL SPECIFICATION |
| ASTM D 276 : 2012 : REDLINE | Standard Test Methods for Identification of Fibers in Textiles |
| MIL-L-60326 Base Document:1965 | LUBRICANT, FLUOROCARBON TELOMER DISPERSION (FOR USE WITH AMMUNITION) |
| ISO/TR 19686-2:2018 | Petroleum products — Equivalency of test method determining the same property — Part 2: Density of petroleum products |
| ASTM D 2766 : 1995 | Standard Test Method for Specific Heat of Liquids and Solids |
| ASTM D 1405/D1405M : 2008 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| MIL-C-81947 Revision A:1975 | COATING COMPOUND, THERMAL INSULATION, THREE-COMPONENT, INTUMESCENT |
| ASTM D 2766 : 1995 : R2000 | Standard Test Method for Specific Heat of Liquids and Solids |
| SAE ARP 4990B : 2015 | TURBINE FLOWMETER FUEL FLOW CALCULATIONS |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| ASTM D 1405/D1405M : 2008 : R2013 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels (Withdrawn 2019) |
| ASTM D 4624 : 1993 : R1998 | Standard Test Method for Measuring Apparent Viscosity by Capillary Viscometer at High Temperature and High-Shear Rates (Withdrawn 2004) |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.