ASTM D 115 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
Available format(s)
Hardcopy , PDF
Superseded date
04-04-2024
Superseded by
Language(s)
English
Published date
14-11-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 09
|
| DocumentType |
Test Method
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment. These test methods include tests for control and performance as follows:
| Procedure | Section |
| Build | 38 – 42 |
| Dielectric Strength | 43 – 48 |
| Drainage | 26 – 32 |
| Flash Point | 18 – 20 |
| Nonvolatile Matter | 21 – 25 |
| Oil Resistance | 54 – 56 |
| Preparation of Test Specimens | 7 |
| Specific Gravity | 9 – 12 |
| Temperature Index | 49 – 50 |
| Time of Drying | 33 – 37 |
| Varnish Compatibility | 51 – 53 |
| Viscosity | 13 – 17 |
1.2Where the entire test method is included in this standard, the precision and bias are not known unless given in the stated method.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.
Note 1:There is no equivalent IEC standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 1711 : 2024 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 1304 : 1999 : R2020 : EDT 1 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| ASTM D 4882 : 2017 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test |
| ASTM D 6053 : 2014 : R2018 | Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes |
| ASTM D 4733 : 2017 | Standard Test Methods for Solventless Electrical Insulating Varnishes |
| ASTM D 7230 : 2006 : R2021 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 3955 : 2020 | Standard Specification for Electrical Insulating Varnishes |
| ASTM D 4209 : 2007 : R2019 | Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes |
| ASTM D 2756 : 2007 : R2017 | Standard Test Method for Weight Loss of Electrical Insulating Varnishes |
| ASTM D 1084 : 2016 : R2021 | Standard Test Methods for Viscosity of Adhesives |
| ASTM D 3251 : 1999 | Standard Test Method for Thermal-Aging Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 202 : 2017 | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
| ASTM D 5423 : 1993 : R2005 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation (Withdrawn 2014) |
| ASTM D 3251 : 2003 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 3278 : 2020 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 1475 : 2013 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 1475 : 1998 : R2012 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 1932 : 2013 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 1932 : 2018 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 3145 : 2003 | Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method |
| ASTM D 5423 : 2022 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
| ASTM D 1932 : 2019 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 2519 : 2001 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 3487 : 2016 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 1475 : 1985 | Standard Test Method for Density of Paint, Varnish, Lacquer, and Related Products |
| ASTM D 3278 : 1996 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 93 : 2019 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM D 202 : 1997 | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
| ASTM D 1475 : 1998 : R2003 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 287 : 2022 | Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer/Method) |
| ASTM D 3251 : 2004 : R2013 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 3145 : 2008 | Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 3251 : 2019 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 3278 : 1982 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus |
| ASTM D 3278 : 2021 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 1932 : 2001 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 3487 : 2000 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 5423 : 2023 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
| ASTM D 56 : 2021 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 2519 : 2007 : R2012 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 1932 : 1997 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 202 : 2023 | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
| ASTM D 1475 : 1960 : R1968 | Standard Method Of Test For Density Of Paint, Varnish, Lacquer, And Related Products |
| ASTM D 2519 : 2019 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 1932 : 2004 : R2009 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 5032 : 2011 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions |
| ASTM D 1475 : 1998 : R2008 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 2519 : 2007 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 3487 : 2008 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 3251 : 2004 : R2009 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 287 : 2012 : REV B | Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method) |
| ASTM D 2518 : 1999 | Standard Specification for Woven Glass Fabrics for Electrical Insulation |
| ASTM D 3487 : 2009 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 3251 : 2004 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 56 : 2021 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 3487 : 2000 : R2006 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 2519 : 2002 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 3487 : 1988 : R1993 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 2518 : 1999 : R2004 | Standard Specification for Woven Glass Fabrics for Electrical Insulation (Withdrawn 2013) |
| ASTM D 2519 : 2019 : REV A | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 5032 : 2019 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions |
| ASTM D 3487 : 2016 : EDT 1 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
| ASTM D 56 : 2022 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 1932 : 2003 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 2519 : 2018 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 3145 : 1997 | Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method |
| ASTM D 56 : 1987 | Standard Test Method for Flash Point by Tag Closed Tester |
| ASTM D 3145 : 2013 | Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method |
| ASTM D 3145 : 2001 | Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method |
| ASTM D 5032 : 1997 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions |
| ASTM D 2519 : 1996 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 1475 : 1998 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 3278 : 1996 : R2004 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 1932 : 2004 | Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 5423 : 1993 : R1999 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
| ASTM D 3278 : 1996 : R2011 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus (Withdrawn 2020) |
| ASTM D 5423 : 2014 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
| ASTM D 93 : 2018 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM D 287 : 2012 : REV B : R2019 | Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method) |
| ASTM D 3145 : 2018 | Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.