ASTM C 666/C666M : 2015 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing
English
08-04-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL 04.02, 2015 Defines the determination of the resistance of concrete specimens to rapidly repeated cycles of freezing and thawing in the laboratory by two different procedures: Procedure A, Rapid Freezing and Thawing in Water, and Procedure B, Rapid Freezing in Air and Thawing in Water.
| Committee |
C 09
|
| DevelopmentNote |
Supersedes ASTM C 666 (09/03)
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1This test method covers the determination of the resistance of concrete specimens to rapidly repeated cycles of freezing and thawing in the laboratory by two different procedures: Procedure A, Rapid Freezing and Thawing in Water, and Procedure B, Rapid Freezing in Air and Thawing in Water. Both procedures are intended for use in determining the effects of variations in the properties of concrete on the resistance of the concrete to the freezing-and-thawing cycles specified in the particular procedure. Neither procedure is intended to provide a quantitative measure of the length of service that may be expected from a specific type of concrete.
1.2The values stated in either inch-pound units or SI units shall be regarded separately as standard. The SI units are shown in brackets. The values stated may not be exact equivalents; therefore each system must be used independently of the other. Combining values from the two units may result in nonconformance.
1.3All material in this test method not specifically designated as belonging to Procedure A or Procedure B applies to either procedure.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ACI 237R : 2007 | SELF-CONSOLIDATING CONCRETE |
| ASTM C 1709 : 2011 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ACI 207.3R : 2018 | REPORT ON PRACTICES FOR EVALUATION OF CONCRETE IN EXISTING MASSIVE STRUCTURES FOR SERVICE CONDITIONS |
| ASTM C 928/C928M : 2013 : REDLINE | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ASTM C 1646/C1646M : 2016 : REDLINE | Standard Practice for Making and Curing Test Specimens for Evaluating Resistance of Coarse Aggregate to Freezing and Thawing in Air-Entrained Concrete |
| ACI 232.1R : 2012 | REPORT ON THE USE OF RAW OR PROCESSED NATURAL POZZOLANS IN CONCRETE |
| ASTM C 457/C457M : 2016 : REDLINE | Standard Test Method for Microscopical Determination of Parameters of the Air-Void System in Hardened Concrete |
| CSA A283 : 2006 | QUALIFICATION CODE FOR CONCRETE TESTING LABORATORIES |
| CSA A283 : 2006 : INC : UPD 2 : 2013 : R201100 | QUALIFICATION CODE FOR CONCRETE TESTING LABORATORIES |
| ASTM C 1582/C1582M : 2011 : R2017 : EDT 1 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| ASTM C 1325 : 2017-02 | SPECIFICATION FOR NON-ASBESTOS FIBER-MAT REINFORCED CEMENTITIOUS BACKER UNITS |
| AASHTO TP 96 : 2013 (R2018) | METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE |
| ASTM E 1512 : 2001 | Standard Test Methods for Testing Bond Performance of Bonded Anchors |
| ASTM C 1776/C1776M : 2017 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
| ASTM E 1512 : 2001 : R2007 | Standard Test Methods for Testing Bond Performance of Bonded Anchors |
| ACI 301 : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| ACI 233R : 2017 | GUIDE TO THE USE OF SLAG CEMENT IN CONCRETE AND MORTAR |
| ACI 349.3R : 2018 | REPORT ON EVALUATION AND REPAIR OF EXISTING NUCLEAR SAFETY-RELATED CONCRETE STRUCTURES |
| CSA A283 : 2006 : R2011 | QUALIFICATION CODE FOR CONCRETE TESTING LABORATORIES |
| ASTM C 1670 : 2013 | Standard Specification for Adhered Manufactured Stone Masonry Veneer (AMSMV) Units |
| ASTM C 330 : 2005 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 1116/C1116M : 2010 | Standard Specification for Fiber-Reinforced Concrete |
| ACI 365.1R : 2017 | REPORT ON SERVICE LIFE PREDICTION |
| ACI 362.1R : 2012 | GUIDE FOR THE DESIGN AND CONSTRUCTION OF DURABLE CONCRETE PARKING STRUCTURES |
| ACI 301M : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| ACI PRC-363.2 : 2011 | GUIDE TO QUALITY CONTROL AND ASSURANCE OF HIGH-STRENGTH CONCRETE |
| ACI 533R : 2011 | GUIDE FOR PRECAST CONCRETE WALL PANELS |
| ACI 544.5R : 2010 | REPORT ON THE PHYSICAL PROPERTIES AND DURABILITY OF FIBER-REINFORCED CONCRETE |
| ACI PRC-506 : 2016 | GUIDE TO SHOTCRETE |
| ACI ITG-8R : 2010 | REPORT ON PERFORMANCE-BASED REQUIREMENTS FOR CONCRETE |
| BS PAS 8820(2016) : 2016 | CONSTRUCTION MATERIALS - ALKALI-ACTIVATED CEMENTITIOUS MATERIAL AND CONCRETE - SPECIFICATION |
| CSA A283 : 2006 : R2016 | QUALIFICATION CODE FOR CONCRETE TESTING LABORATORIES |
| ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
| ASTM D 8139 : 2017 | Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM E 2392 : 2005 | Standard Guide for Design of Earthen Wall Building Systems |
| ASTM C 1622/C1622M : 2010 | Standard Specification for Cold-Weather Admixture Systems |
| ASTM C 1116/C1116M : 2010 : REV A : R2015 | Standard Specification for Fiber-Reinforced Concrete |
| ACI 305R : 2010 | GUIDE TO HOT WEATHER CONCRETING |
| ACI 304.2R : 2017 | GUIDE TO PLACING CONCRETE BY PUMPING METHODS |
| ACI 549.5R : 2016 | REPORT ON SPRAY-UP AND CONTINUOUS STRAND GLASS FIBER-REINFORCED CONCRETE (GFRC) |
| AASHTO TP 96 : 2013 | METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE |
| ASTM C 688 : 2014 : REDLINE | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 341/C341M : 2014-01 | PRACTICE FOR PREPARATION AND CONDITIONING OF CAST, DRILLED, OR SAWED SPECIMENS OF HYDRAULIC-CEMENT MORTAR AND CONCRETE USED FOR LENGTH CHANGE MEASUREMENTS |
| ACI 325.14R : 2017 | GUIDE FOR DESIGN AND PROPORTIONING OF CONCRETE MIXTURES FOR PAVEMENTS |
| ACI PRC-548.3 : 2009 | REPORT ON POLYMER-MODIFIED CONCRETE |
| AASHTO M 194M/M 194 : 1900 | SPECIFICATION FOR CHEMICAL ADMIXTURES FOR CONCRETE |
| ACI 364.3R : 2009 | GUIDE FOR CEMENTITIOUS REPAIR MATERIAL DATA SHEET |
| ACI 345R : 2011 | GUIDE FOR CONCRETE HIGHWAY BRIDGE DECK CONSTRUCTION |
| ASTM C 1116/C1116M : 2010 : REV A | Standard Specification for Fiber-Reinforced Concrete |
| ASTM E 1512 : 2001 : R2015 | Standard Test Methods for Testing Bond Performance of Bonded Anchors |
| ACI 522R : 2010(R2011) | REPORT ON PERVIOUS CONCRETE |
| ACI 522R : 2010 | REPORT ON PERVIOUS CONCRETE |
| ASTM C 226 : 2012 : REDLINE | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ACI 207.5R : 2011 | REPORT ON ROLLER-COMPACTED MASS CONCRETE |
| ACI 363R : 2010 | REPORT ON HIGH-STRENGTH CONCRETE |
| ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 | Standard Specification for Cold-Weather Admixture Systems |
| ASTM C 1856/C1856M : 2017 | Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete |
| CSA S304 : 2014 | DESIGN OF MASONRY STRUCTURES |
| ACI PRC-308 : 2016 | GUIDE TO EXTERNAL CURING OF CONCRETE |
| CSA A3000 : 2013 | CEMENTITIOUS MATERIALS COMPENDIUM |
| AASHTO TP 118 : 2015 | METHOD OF TEST FOR CHARACTERIZATION OF THE AIR-VOID SYSTEM OF FRESHLY MIXED CONCRETE BY THE SEQUENTIAL PRESSURE METHOD |
| ASTM C 1582/C1582M : 2011 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| CSA A23.1 A23.2 : 2014 | CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE |
| ASTM C 823 : 2000 | Standard Practice for Examination and Sampling of Hardened Concrete in Constructions |
| ASTM C 341/C341M : 2014-01 | PRACTICE FOR PREPARATION AND CONDITIONING OF CAST, DRILLED, OR SAWED SPECIMENS OF HYDRAULIC-CEMENT MORTAR AND CONCRETE USED FOR LENGTH CHANGE MEASUREMENTS |
| ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
| ASTM C 215 : 2014 : REDLINE | Standard Test Method for Fundamental Transverse, Longitudinal, and<brk/> Torsional Resonant Frequencies of Concrete Specimens |
| ASTM C 157/C157M : 2017 : REDLINE | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 670 : 2015 : REDLINE | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.