ASTM C 297 : 1994 : R1999
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions
Hardcopy , PDF
11-11-2014
English
10-06-1999
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 15.03, 2003 Determines the core flat wise tension strength or the bond between core and facings of an assembled sandwich panel.
| Committee |
D 30
|
| DocumentType |
Test Method
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This test method covers the determination of the core flatwise tension strength, or the bond between core and facings of an assembled sandwich panel. The test consists of subjecting a sandwich construction to a tensile load normal to the plane of the sandwich, such load being transmitted to the sandwich through thick loading blocks bonded to the sandwich facings or directly to the core.
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given may be approximate.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| SAE AMS 3912 : 2014 | RADOMES, FOAM SANDWICH, POLYIMIDE/QUARTZ CLOTH CONSTRUCTION |
| MIL-A-85705 Revision A:1987 | ADHESIVE, AIRCRAFT, FOR STRUCTURAL REPAIR |
| SAE AMS 3695 : 2014 | ADHESIVE FILM, EPOXY-BASE, FOR HIGH DURABILITY STRUCTURAL ADHESIVE BONDING |
| I.S. EN 16245-5:2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 5: SPECIFIC REQUIREMENTS FOR CORE MATERIALS |
| UNI EN 16245-5 : 2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 5: SPECIFIC REQUIREMENTS FOR CORE MATERIALS |
| BS EN 16245-5:2013 | Fibre-reinforced plastic composites. Declaration of raw material characteristics Specific requirements for core materials |
| MIL-HDBK-349 Base Document:1994 | MANUFACTURE AND INSPECTION OF ADHESIVE BONDED, ALUMINUM HONEYCOMB SANDWICH ASSEMBLIES FOR AIRCRAFT |
| SAE AMS 2980/1 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 1 - GENERAL REQUIREMENTS |
| SAE AMS 3970/1 : 2011 | CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 1 - GENERAL REQUIREMENTS |
| SAE AMS 3710 : 2014 | SANDWICH STRUCTURES, GLASS FABRIC-RESIN, LOW PRESSURE MOLDED, HEAT RESISTANT |
| SAE AMS STD 401 : 1999 | SANDWICH CONSTRUCTIONS AND CORE MATERIALS - GENERAL TEST METHODS |
| DIN EN 16245-5:2013-08 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 5: Specific requirements for core materials |
| 11/30239986 DC : DRAFT MAR 2011 | BS EN 16245-5 - FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 5: SPECIFIC REQUIREMENTS FOR CORE MATERIALS |
| SAE AMS 3970/6 : 2011 | CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 6 - MATERIAL SPECIFICATION: CARBON FIBER FABRIC REINFORCED EPOXY PREPREG FOR REPAIR, PLAIN WEAVE FABRIC, 193 G/M[2], ADHESIVE FILM FOR REPAIR AND NON-STRUCTURAL GLASS FIBER FABRIC REINFORCED EPOXY PREPREG, 105 G/M[2] |
| MIL-A-25463 Revision B:1982 | ADHESIVE, FILM FORM, METALLIC STRUCTURAL SANDWICH CONSTRUCTION |
| DIN SPEC 91326:2016-09 | FIRE RETARDANT, MULTIAXIAL REINFORCED COMPOSITE PARTS, MANUFACTURED IN VACUUM PROCESS TECHNOLOGIES FOR RAILWAY VEHICLE APPLICATIONS |
| UNE-EN 16245-5:2014 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 5: Specific requirements for core materials |
| MIL-STD-401 Revision B:1967 | SANDWICH CONSTRUCTIONS AND CORE MATERIALS, GENERAL TEST METHODS |
| SAE AIR 6291 : 2014 | GUIDELINES FOR REPAIR PROCESS EVALUATION OF ALUMINUM BONDED STRUCTURE |
| ANSI/EIMA 99A : 2001 | EXTERIOR INSULATION AND FINISH SYSTEMS (EIFS) |
| EN 16245-5:2013 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 5: Specific requirements for core materials |
| SAE AMS A 25463 : 2013 | ADHESIVE, FILM FORM, METALLIC STRUCTURAL SANDWICH CONSTRUCTION |
| SAE AMS 3913 : 2014 | RADOME, FOAM SANDWICH, HOT-MELT, ADDITION-TYPE POLYIMIDE |
| SAE AMS 3686 : 2014 | ADHESIVE, POLYIMIDE RESIN, FILM AND PASTE HIGH TEMPERATURE RESISTANT, 315 DEGREES C (599 DEGREES F) |
| SAE AMS 3092 : 2015 | RELEASE AGENT, FOR USE DURING FORM-IN-PLACE GASKET PREPARATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.