ASTM C 157/C157M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete
Hardcopy , PDF
19-08-2024
English
15-08-2017
This test method covers the determination of the length changes that are produced by causes other than externally applied forces and temperature changes in hardened hydraulic-cement mortar and concrete specimens made in the laboratory and exposed to controlled conditions of temperature and moisture.
| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the length changes that are produced by causes other than externally applied forces and temperature changes in hardened hydraulic-cement mortar and concrete specimens made in the laboratory and exposed to controlled conditions of temperature and moisture.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E11. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1105 : 2023 : REV A | Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction |
| ASTM C 928/C928M : 2020 : REV A | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ASTM C 311/C311M : 2024 | Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete |
| ASTM C 1107/C1107M : 2020 | Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink) |
| ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
| ASTM C 183/C183M : 2023 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
| ASTM C 1698 : 2019 | Standard Test Method for Autogenous Strain of Cement Paste and Mortar |
| ASTM C 1012/C1012M : 2024 | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
| ASTM C 331/C331M : 2023 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM C 1856/C1856M : 2017 | Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete |
| ASTM C 494/C494M : 2024 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 1670/C1670M : 2024 | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM C 806 : 2023 | Standard Test Method for Restrained Expansion of Expansive Cement Mortar |
| ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM C 1708/C1708M : 2023 | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
| ASTM C 688 : 2022 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 1293/C1293M : 2023 : REV A | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM C 1709 : 2022 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ASTM C 1582/C1582M : 2011 : R2017 : EDT 1 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| ASTM C 330/C330M : 2023 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 511 : 2021 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 1437 : 2001 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 305 : 2014 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
| ASTM C 596 : 2023 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
| ASTM E 11 : 2024 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 1437 : 2013 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM E 337 : 2015 : R2023 | Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures) |
| ASTM E 337 : 2015 | Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures) |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 511 : 2019 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
| ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1437 : 2007 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1437 : 2015 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 1437 : 1999 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.