ASTM C 1481 : 2012 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
Hardcopy , PDF
06-06-2024
English
01-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.07, 2017 Specifies the use of single and multicomponent, cold-applied joint sealants, or precured sealant systems for joint sealing applications, or both, in buildings using Exterior Insulation and Finish Systems (EIFS) on one or both sides of the joint.
| Committee |
C 24
|
| DocumentType |
Guide
|
| Pages |
6
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide describes the use of single and multi-component, cold-applied joint sealants, or precured sealant systems for joint sealing applications, or both, in buildings using Exterior Insulation and Finish Systems (EIFS) on one or both sides of the joint. Refer to 10.1 for joint seal geometries.
1.2The elastomeric sealants described by this guide meet the requirements of Specifications C834, C920, or C1311.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5There are no ISO standards similar or equivalent to this ASTM standard.
| ASTM C 1193 : 2016 | Standard Guide for Use of Joint Sealants |
| ASTM C 1535 : 2005 : R2017 | Standard Practice for Application of Exterior Insulation and Finish Systems Class PI |
| ASTM C 1472 : 2016 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1535 : 2005 : R2023 | Standard Practice for Application of Exterior Insulation and Finish Systems Class PI |
| ASTM C 1382 : 2002 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM E 2568 : 2009 : EDT 1 | Standard Specification for PB Exterior Insulation and Finish Systems |
| ASTM C 1193 : 2011 : REV A | Standard Guide for Use of Joint Sealants |
| ASTM C 794 : 2018 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
| ASTM C 1193 : 2016 : R2023 | Standard Guide for Use of Joint Sealants |
| ASTM C 719 : 2022 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
| ASTM C 1472 : 2016 : REDLINE | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1472 : 2005 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1193 : 2016 | Standard Guide for Use of Joint Sealants |
| ASTM C 1397 : 2013 : R2019 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage |
| ASTM E 2110 : 2003 | Standard Terminology for Exterior Insulation and Finish Systems (EIFS) |
| ASTM E 2511 : 2017 | Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies |
| ASTM C 1472 : 2010 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1397 : 2004 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems |
| ASTM C 1472 : 2006 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1382 : 2011 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 1311 : 2002 | Standard Specification for Solvent Release Sealants |
| ASTM C 1193 : 2005 : REV A | Standard Guide for Use of Joint Sealants |
| ASTM C 717 : 2019 | Standard Terminology of Building Seals and Sealants |
| ASTM C 1472 : 2016 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 834 : 2017 : R2023 | Standard Specification for Latex Sealants |
| ASTM C 1311 : 1995 | Standard Specification for Solvent Release Sealants |
| ASTM E 2568 : 2017 | Standard Specification for PB Exterior Insulation and Finish Systems |
| ASTM C 1193 : 2016 : REDLINE | Standard Guide for Use of Joint Sealants |
| ASTM C 1397 : 2013 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage |
| ASTM C 1397 : 2009 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage |
| ASTM C 1382 : 2016 : REDLINE | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 1311 : 2010 | Standard Specification for Solvent Release Sealants |
| ASTM E 2511 : 2009 | Standard Guide for Detailing of EIFS-Clad Wall Assemblies |
| ASTM C 1193 : 2012 | Standard Guide for Use of Joint Sealants |
| ASTM C 1311 : 2014 | Standard Specification for Solvent Release Sealants |
| ASTM E 2110 : 2017 | Standard Terminology for Exterior Insulation and Finish Systems (EIFS) |
| ASTM E 2511 : 2017 : R2023 | Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies |
| ASTM C 834 : 2017 | Standard Specification for Latex Sealants |
| ASTM C 1472 : 2016 : R2022 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM E 2110 : 2009 : EDT 1 | Standard Terminology for Exterior Insulation and Finish Systems (EIFS) |
| ASTM C 1193 : 2005 | Standard Guide for Use of Joint Sealants |
| ASTM C 794 : 2018 : R2022 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
| ASTM C 1382 : 2005 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 834 : 2017 : REDLINE | Standard Specification for Latex Sealants |
| ASTM C 1311 : 2014 : REDLINE | Standard Specification for Solvent Release Sealants |
| ASTM C 719 : 2014 : R2019 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
| ASTM E 2568 : 2017 : REV A | Standard Specification for PB Exterior Insulation and Finish Systems |
| ASTM C 1193 : 2000 | Standard Guide for Use of Joint Sealants |
| ASTM C 1397 : 2002 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems |
| ASTM C 1311 : 2022 | Standard Specification for Solvent Release Sealants |
| ASTM C 1472 : 2016 : EDT 1 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1397 : 2005 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems |
| ASTM E 2110 : 2011 | Standard Terminology for Exterior Insulation and Finish Systems (EIFS) |
| ASTM C 1382 : 1997 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 1382 : 2004 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 717 : 2024 | Standard Terminology of Building Seals and Sealants |
| ASTM C 1382 : 2016 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 1193 : 2011 | Standard Guide for Use of Joint Sealants |
| ASTM C 1397 : 1998 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems |
| ASTM E 2511 : 2017 : REDLINE | Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies |
| ASTM C 1472 : 2000 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1193 : 2013 | Standard Guide for Use of Joint Sealants |
| ASTM E 2110 : 2000 | Standard Terminology for Exterior Insulation and Finish Systems (EIFS) |
| ASTM C 1382 : 2016 : R2023 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM E 2110 : 2017 : REDLINE | Standard Terminology for Exterior Insulation and Finish Systems (EIFS) |
| ASTM E 2568 : 2007 | Standard Specification for PB Exterior Insulation and Finish Systems |
| ASTM C 1397 : 2003 | Standard Practice for Application of Class PB Exterior Insulation and Finish Systems |
| ASTM C 1193 : 2009 | Standard Guide for Use of Joint Sealants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.