ASTM C 1442 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
Hardcopy , PDF
11-11-2014
English
01-01-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
C 24
|
| DocumentType |
Standard Practice
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This practice covers three types of laboratory weathering exposure procedures for evaluating the effect of actinic radiation, heat, and moisture on sealants.
1.2 The exposure sources used in the three types of artificial weathering devices are the filtered xenon arc, fluorescent ultraviolet lamps, and open flame carbon arc based on Practices G 155, G 154, and G 152, respectively.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.
1.4 The ISO standard related to this Practice is ISO 11431. Significant differences exist between the procedures. The ISO specimens are exposed through glass and are elongated prior to examination for loss of adhesion or cohesion, or both, following exposure.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1021 : 2008 : R2019 | Standard Practice for Laboratories Engaged in Testing of Building Sealants |
| ASTM C 1523 : 2017 | Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants |
| ASTM C 1257 : 2015 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
| ASTM C 793 : 2005 : R2017 | Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants |
| ASTM C 510 : 2016 | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
| ASTM C 920 : 2018 | Standard Specification for Elastomeric Joint Sealants |
| ASTM C 1382 : 2016 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
| ASTM C 1311 : 2014 | Standard Specification for Solvent Release Sealants |
| ASTM C 732 : 2017 | Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants |
| ASTM C 957/C957M : 2017 | Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Integral Wearing Surface |
| ASTM C 1501 : 2019 | Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures |
| ASTM C 1518 : 2016 | Standard Specification for Precured Elastomeric Silicone Joint Sealants |
| ASTM E 2785 : 2014 | Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions |
| ASTM C 1519 : 2010 : R2017 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
| ASTM C 734 : 2015 | Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering |
| ASTM C 1184 : 2018 : EDT 1 | Standard Specification for Structural Silicone Sealants |
| ASTM C 1193 : 2016 | Standard Guide for Use of Joint Sealants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.