ASTM C 1437 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Flow of Hydraulic Cement Mortar
Hardcopy , PDF
22-10-2020
English
30-12-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of flow of hydraulic cement mortars.
| Committee |
C 01
|
| DocumentType |
Test Method
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of flow of hydraulic cement mortars.
1.2The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. When combined standards are cited, the selection of the measurement systems is at the user’s discretion subject to the requirements of the referenced standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1384 : 2018 : EDT 1 | Standard Specification for Admixtures for Masonry Mortars |
| ASTM C 942/C942M : 2021 | Standard Test Method for Compressive Strength of Grouts for Preplaced-Aggregate Concrete in the Laboratory |
| ASTM A 1081/A1081M : 2021 | Standard Test Method for Evaluating Bond of Seven-Wire Steel Prestressing Strand |
| ASTM C 1072 : 2022 | Standard Test Methods for Measurement of Masonry Flexural Bond Strength |
| ASTM C 1107/C1107M : 2020 | Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink) |
| ASTM C 219 : 2020 : REV A | Standard Terminology Relating to Hydraulic and Other Inorganic Cements |
| ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 1038/C1038M : 2019 | Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water |
| ASTM C 348 : 2021 | Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1403 : 2022 : REV A | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
| ASTM C 1240 : 2020 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 563 : 2020 | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
| ASTM C 989/C989M : 2022 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 1600/C1600M : 2019 | Standard Specification for Rapid Hardening Hydraulic Cement |
| ASTM C 1567 : 2022 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 311/C311M : 2022 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
| ASTM C 157/C157M : 2017 | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 1714/C1714M : 2019 : REV A | Standard Specification for Preblended Dry Mortar Mix for Unit Masonry |
| ASTM C 1240 : 2015 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM A 1081/A1081M : 2015 | Standard Test Method for Evaluating Bond of Seven-Wire Steel Prestressing Strand |
| ASTM C 1600/C1600M : 2018 | Standard Specification for Rapid Hardening Hydraulic Cement |
| ASTM C 1403 : 2015 | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
| ASTM C 1506 : 2017 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
| ASTM C 387/C387M : 2017 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
| ASTM C 1581/C1581M : 2018 : REV A | Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage |
| ASTM C 230/C230M : 2014 | Standard Specification for Flow Table for Use in Tests of Hydraulic Cement |
| ASTM C 596 : 2018 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
| ASTM C 1439 : 2013 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 942 : 2015 | Standard Test Method for Compressive Strength of Grouts for Preplaced-Aggregate Concrete in the Laboratory |
| ASTM C 441/C441M : 2017 | Standard Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction |
| ASTM C 1567 : 2013 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
| ASTM C 989/C989M : 2018 : REV A | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 1856/C1856M : 2017 | Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete |
| ASTM C 1038/C1038M : 2014 : REV B | Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water |
| ASTM C 1072 : 2013 : EDT 1 | Standard Test Methods for Measurement of Masonry Flexural Bond Strength |
| ASTM C 348 : 2018 | Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars |
| ASTM C 311/C311M : 2018 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
| ASTM C 1107/C1107M : 2017 | Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink) |
| ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 125 : 2019 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 827/C827M : 2016 | Standard Test Method for Change in Height at Early Ages of Cylindrical Specimens of Cementitious Mixtures |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.