ASTM C 142/C142M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Clay Lumps and Friable Particles in Aggregates
Hardcopy , PDF
19-10-2023
English
24-05-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This test method covers the approximate determination of clay lumps and friable particles in aggregates.
| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the approximate determination of clay lumps and friable particles in aggregates.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1:Sieve sizes openings are identified by their Specification E11 designation with their alternative Specification E11 designation given in parentheses for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 1139/D1139M : 2022 | Standard Specification for Aggregate for Single or Multiple Asphalt Surface Treatments |
| ASTM C 144 : 2018 | Standard Specification for Aggregate for Masonry Mortar |
| ASTM D 5106 : 2022 | Standard Specification for Steel Slag Aggregates for Asphalt Paving Mixtures |
| ASTM D 6155 : 2019 | Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures |
| ASTM D 8099/D8099M : 2017 : R2023 | Standard Specification for Asphalt Emulsion Pavement Sealer (Mineral Colloid or Chemically Stabilized Type) |
| ASTM C 331/C331M : 2023 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM C 897 : 2015 : R2020 | Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters |
| ASTM C 404 : 2018 | Standard Specification for Aggregates for Masonry Grout |
| ASTM C 1761/C1761M : 2023 | Standard Specification for Lightweight Aggregate for Internal Curing of Concrete |
| ASTM C 33/C33M : 2023 | Standard Specification for Concrete Aggregates |
| ASTM D 6945/D6945M : 2003 : R2023 | Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade) |
| ASTM C 330/C330M : 2023 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 33/C33M : 2023 | Standard Specification for Concrete Aggregates |
| ASTM C 1005 : 2019 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 33/C33M : 2018 | Standard Specification for Concrete Aggregates |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 1005 : 2000 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 1005 : 2017 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 1005 : 2010 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1005 : 2018 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1005 : 2005 | Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.