ASTM C 128 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
Hardcopy , PDF
10-01-2023
English
17-03-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of relative density (specific gravity) and the absorption of fine aggregates.
| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of relative density (specific gravity) and the absorption of fine aggregates. The relative density (specific gravity), a dimensionless quality, is expressed as oven-dry (OD), saturated-surface-dry (SSD), or as apparent relative density (specific gravity). The OD relative density is determined after drying the aggregate. The SSD relative density and absorption are determined after soaking the aggregate in water for a prescribed duration.
1.2This test method is not intended to be used for lightweight aggregates that comply with Specification C332 Group I aggregates.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1810/C1810M : 2022 | Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures |
| ACI PRC-308-213-13:2013(R2022) | Report on Internally Cured Concrete Using Prewetted Absorptive Lightweight Aggregate |
| ASTM C 127 : 2015 | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024) |
| ASTM C 566 : 2019 | Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying |
| ASTM D 4469 : 2017 | Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in Asphalt Mixtures |
| ASTM C 1688/C1688M : 2014 : REV A | Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete (Withdrawn 2023) |
| ASTM D 6932/D6932M : 2021 | Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Asphalt Mixtures |
| ASTM C 702/C702M : 2018 | Standard Practice for Reducing Samples of Aggregate to Testing Size |
| ASTM C 144 : 2018 | Standard Specification for Aggregate for Masonry Mortar |
| ASTM C 192/C192M : 2019 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM D 6995 : 2021 | Standard Test Method for Determining Field VMA Based on the Maximum Specific Gravity of an Asphalt Mixture (G<inf>mm</inf>) |
| ASTM C 1800/C1800M : 2016 | Standard Test Method for Determining Density of Roller-Compacted Concrete Specimens Using the Gyratory Compactor |
| ASTM C 1260 : 2022 | Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method) |
| ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM D 8140 : 2018 | Standard Guide for the Use of Foundry Sand in Asphalt Mixtures |
| ASTM C 1810/C1810M : 2021 : REV A | Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures |
| ASTM C 330/C330M : 2017 : REV A | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM D 3910 : 2021 | Standard Practices for Design, Testing, and Construction of Slurry Seal |
| ASTM D 2172/D2172M : 2017 : EDT 1 | Standard Test Methods for Quantitative Extraction of Asphalt Binder from Asphalt Mixtures |
| ASTM D 4215 : 2021 | Standard Specification for Cold-Mixed, Cold-Laid Asphalt Paving Mixtures |
| ASTM D 6023 : 2016 | Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM) |
| ASTM C 1077 : 2017 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 1761/C1761M : 2017 | Standard Specification for Lightweight Aggregate for Internal Curing of Concrete |
| ASTM C 70 : 2020 | Standard Test Method for Surface Moisture in Fine Aggregate |
| ASTM C 604 : 2018 | Standard Test Method for True Specific Gravity of Refractory Materials by Gas-Comparison Pycnometer |
| ASTM D 4460 : 2022 : REV A | Standard Practice for Calculating Precision Limits Where Values Are Calculated from Other Test Methods |
| ASTM D 7564/D7564M : 2016 | Standard Practice for Construction of Asphalt-Rubber Cape Seal |
| ASTM D 7370/D7370M : 2014 : R2021 | Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse, and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion |
| ASTM C 1567 : 2022 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
| ASTM C 123/C123M : 2014 | Standard Test Method for Lightweight Particles in Aggregate (Withdrawn 2023) |
| ASTM C 780 : 2020 | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
| ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
| ASTM C 29/C29M : 2017 : REV A | Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate |
| ASTM C 637 : 2020 | Standard Specification for Aggregates for Radiation-Shielding Concrete |
| ASTM C 404 : 2018 | Standard Specification for Aggregates for Masonry Grout |
| AASHTO R 18:2018 | Standard Practice for Establishing and Implementing a Quality Management System for Construction Materials Testing Laboratories, Single User PDF Download<br> |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1252 : 1998 | Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) |
| ASTM C 1252 : 2017 | Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) |
| ASTM C 1252 : 2006 | Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) (Withdrawn 2015) |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1252 : 2003 | Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 330 : 2000 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 330 : 1999 | Standard Specification for Lightweight Aggregates For Structural Concrete |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.