ASTM C 1193 : 2016 : REDLINE
Current
The latest, up-to-date edition.
Standard Guide for Use of Joint Sealants
English
13-01-2016
CONTAINED IN VOL. 04.07, 2018 Specifies the use of a cold liquid-applied sealant for joint sealing applications.
Committee |
C 24
|
DevelopmentNote |
Supersedes ASTM C 790, ASTM C 804 and ASTM C 962 (12/2001)
|
DocumentType |
Redline
|
Pages |
33
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
1.1This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.
1.2An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C834, C920, or C1311.
1.3This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C1249 should be consulted for this information.
1.4Practice C919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required.
1.5This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others.
1.6The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only.
1.7The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
1.9The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.
ASTM C 1564 : 2015 : REDLINE | Standard Guide for Use of Silicone Sealants for Protective Glazing Systems |
ASTM E 2435 : 2005 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
ASTM C 1127/C1127M : 2015 : REDLINE | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface |
ASTM E 2112 : 2007 : R2016 | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
ASTM C 1481 : 2012 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 898 : 2001 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Separate Wearing Course |
ASTM C 1242 : 2018-03 | GUIDE FOR SELECTION, DESIGN, AND INSTALLATION OF DIMENSION STONE ATTACHMENT SYSTEMS |
ASTM E 2112 : 2007 | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
ASTM E 2266 : 2011 : REDLINE | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM C 898/C898M : 2009 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Separate Wearing Course |
ASTM C 1311 : 2014 : REDLINE | Standard Specification for Solvent Release Sealants |
ASTM C 981:2005 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM C 1736 : 2011 | Standard Practice for Non-Destructive Evaluation of Adhesion of Installed Weatherproofing Sealant Joints Using a Rolling Device (Withdrawn 2020) |
ASTM C 898/C898M : 2009 : R2017 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course |
ASTM E 241 : 2009 | Standard Guide for Limiting Water-Induced Damage to Buildings |
ASTM C 919 : 2012 : R2017 | Standard Practice for Use of Sealants in Acoustical Applications |
ASTM E 2435 : 2005 : R2010 : EDT 1 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
ACI 303.1 : 1997 | STANDARD SPECIFICATION FOR CAST-IN-PLACE ARCHITECTURAL CONCRETE |
ACI 533R : 2011 | GUIDE FOR PRECAST CONCRETE WALL PANELS |
ASTM E 2813 : 2012 | Standard Practice for Building Enclosure Commissioning |
ASTM E 2813 : 2012 : EDT 1 | Standard Practice for Building Enclosure Commissioning |
ASTM C 1521 : 2013 : REDLINE | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
CSA A440.4 : 2007 : R2016 | WINDOW, DOOR, AND SKYLIGHT INSTALLATION |
CSA A440.4 : 2007 | WINDOW, DOOR, AND SKYLIGHT INSTALLATION |
ASTM C 1481 : 2012 : R2017 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 834 : 2017 : REDLINE | Standard Specification for Latex Sealants |
ASTM C 920 : 2018 : REDLINE | Standard Specification for Elastomeric Joint Sealants |
ASTM C 981 : 2005 : R2013 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM E 241 : 2009 : R2014 : EDT 1 | Standard Guide for Limiting Water-Induced Damage to Buildings |
ASTM C 1401 : 2014 : REDLINE | Standard Guide for Structural Sealant Glazing |
ASTM E 2435 : 2005 : R2015 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
ASTM C 919 : 2012 | Standard Practice for Use of Sealants in Acoustical Applications |
ASTM C 1472 : 2016 : REDLINE | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 510 : 2016 : REDLINE | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
ASTM C 1401 : 2014 : REDLINE | Standard Guide for Structural Sealant Glazing |
ASTM C 1442 : 2014 : REDLINE | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM C 1472 : 2016 : REDLINE | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1521 : 2013 : REDLINE | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 1265 : 2017 : REDLINE | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
ASTM C 1247 : 2014 : REDLINE | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
ASTM C 731 : 2015 : REDLINE | Standard Test Method for Extrudability, After Package Aging, of Latex Sealants |
ASTM C 711 : 2014 : REDLINE | Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants |
ASTM C 734 : 2015 : REDLINE | Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering |
ASTM C 661 : 2015 : REDLINE | Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer |
ASTM C 1382 : 2016 : REDLINE | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 732 : 2017 : REDLINE | Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants |
ASTM C 834 : 2017 : REDLINE | Standard Specification for Latex Sealants |
ASTM D 2453 : 2015 : REDLINE | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
ASTM C 1311 : 2014 : REDLINE | Standard Specification for Solvent Release Sealants |
ASTM C 1241 : 2014 : REDLINE | Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
ASTM C 792 : 2015 : REDLINE | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants |
ASTM C 1257 : 2015 : REDLINE | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM C 1087 : 2016 : REDLINE | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM E 2114 : 2017-03 | TERMINOLOGY FOR SUSTAINABILITY RELATIVE TO THE PERFORMANCE OF BUILDINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.