ASTM B 827 : 2005 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests
Hardcopy , PDF
27-08-2020
English
01-10-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.04, 2015 Gives procedures for conducting environmental tests involving exposures to controlled quantities of corrosive gas mixtures.
| Committee |
B 02
|
| DocumentType |
Standard Practice
|
| Pages |
9
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice provides procedures for conducting environmental tests involving exposures to controlled quantities of corrosive gas mixtures.
1.2This practice provides for the required equipment and methods for gas, temperature, and humidity control which enable tests to be conducted in a reproducible manner. Reproducibility is measured through the use of control coupons whose corrosion films are evaluated by mass gain, coulometry, or by various electron and X-ray beam analysis techniques. Reproducibility can also be measured by in situ corrosion rate monitors using electrical resistance or mass/frequency change methods.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. See 5.1.2.4.
| ASTM D 3824 : 1995 : R2000 | Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by the Chemiluminescent Method |
| ASTM E 902 : 2005 | Standard Practice for Checking the Operating Characteristics of X-Ray Photoelectron Spectrometers (Withdrawn 2011) |
| ASTM D 3464 : 1996 : R2001 | Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer |
| ASTM D 2914 : 2001 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 3464 : 1996 | Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer |
| ASTM D 4230 : 2002 | Standard Test Method of Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer |
| ASTM D 3609 : 2000 : R2014 | Standard Practice for Calibration Techniques Using Permeation Tubes |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM D 3824 : 1995 : R2005 | Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by the Chemiluminescent Method |
| ASTM D 2914 : 2001 : R2007 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 3824 : 2012 : REDLINE | Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by the Chemiluminescent Method |
| ASTM B 845 : 1997 | Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts |
| ASTM D 4230 : 2002 : R2007 | Standard Test Method of Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM D 4230 : 2002 : R2012 | Standard Test Method of Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer |
| ASTM B 542 : 2013 : REDLINE | Standard Terminology Relating to Electrical Contacts and Their Use |
| ASTM D 2914 : 1995 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 3609 : 2000 : R2005 | Standard Practice for Calibration Techniques Using Permeation Tubes |
| ASTM D 3464 : 1996 : R2007 | Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer |
| ASTM D 3609 : 2000 : R2010 | Standard Practice for Calibration Techniques Using Permeation Tubes |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM D 3609 : 2000 | Standard Practice for Calibration Techniques Using Permeation Tubes |
| ASTM B 765 : 2003 : R2018 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
| ASTM D 4230 : 1983 : R1996 : EDT 1 | Standard Test Method of Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer |
| ASTM D 4230 : 2002 : EDT 1 | Standard Test Method of Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer |
| ASTM D 2914 : 2015 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 3464 : 1996 : R2014 | Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM D 2914 : 2015 : REDLINE | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM D 3824 : 2012 | Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by the Chemiluminescent Method |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
| ASTM D 2912 : 1976 : R1983 | Test Method for Oxidant Content of the Atmosphere (Neutral KI) (Withdrawn 1990) |
| ASTM D 4230 : 2020 | Standard Test Method for Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.