ASTM B 788/B788M : 2009 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe
Hardcopy , PDF
01-10-2020
English
01-05-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.02, 2015 Specifies procedures, soils, and soil placement for the proper installation of corrugated aluminum culverts and storm sewers in either trench or projection installations.
| Committee |
B 07
|
| DevelopmentNote |
Supersedes ASTM B 788. (11/2004)
|
| DocumentType |
Standard Practice
|
| Pages |
5
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes procedures, soils, and soil placement for the proper installation of corrugated aluminum culverts and storm sewers in either trench or projection installations. A typical trench installation is shown in Fig. 1, and a typical embankment (projection) installation is shown in Fig. 2. The pipes described in this practice are manufactured in a factory and furnished to the job in lengths ordinarily from 10 to 30 ft [3 to 9 m], with 20 ft [6 m] being common, for field joining. This practice applies to structures designed in accordance with Practice B790/B790M.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.2.1SI Units—SI units are shown in the text in brackets, and they are the applicable values for metric installation.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 2937 : 2000 : EDT 1 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 2487 : 2017 : EDT 1 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 6938 : 2008 : REV A | Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 6938 : 2010 | Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM B 790/B790M : 2016 : REDLINE | Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits |
| ASTM D 1556 : 2007 | Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method |
| ASTM D 6938 : 2015 | Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM B 745/B745M : 2015 : REDLINE | Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains |
| ASTM D 1556 : 2000 | Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method |
| ASTM D 6938 : 2017 : REV A | Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 2937 : 2017 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 6938 : 2008 | Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 2167 : 2015 : REDLINE | Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method |
| ASTM D 6938 : 2017-03 | TEST METHOD FOR IN-PLACE DENSITY AND WATER CONTENT OF SOIL AND SOIL-AGGREGATE BY NUCLEAR METHODS (SHALLOW DEPTH) |
| ASTM D 698 : 2013-05 | TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3])) |
| ASTM D 2167 : 1994 | Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method |
| ASTM D 2937 : 2017 : EDT 2 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 2937 : 2017-03 | TEST METHOD FOR DENSITY OF SOIL IN PLACE BY THE DRIVE-CYLINDER METHOD |
| ASTM D 6938 : 2007 : REV A | Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 2937 : 2010 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 2937 : 2000 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 6938 : 2006 : EDT 1 | Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 2487 : 2006 : EDT 1 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 6938 : 2017 | Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 2937 : 2017 : EDT 1 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 2487 : 2010 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2487 : 2000 | Standard Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2487 : 2006 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2487 : 2011 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2167 : 2015 | Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method (Withdrawn 2024) |
| ASTM D 2937 : 2004 | Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method |
| ASTM D 2487 : 2017 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 6938 : 2007 : REV B | Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
| ASTM D 2487 : 1969 : R1975 | Standard Test Method for Classification Of Soils For Engineering Purposes |
| ASTM D 2167 : 2008 | Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.