Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM B 335 : 2003 : R2018

Current

Current

The latest, up-to-date edition.

Standard Specification for Nickel-Molybdenum Alloy Rod

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-11-2018

$90.04
Including GST where applicable

CONTAINED IN VOL. 02.04, 2015 Defines rod of nickel-molybdenum alloys (UNS N10001, N10665, N10675, N10629, and N10624) for use in general corrosive service.

Committee
B 02
DocumentType
Standard
Pages
4
ProductNote
Reconfirmed 2003
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This specification2 covers rod of nickel-molybdenum alloys (UNS N10001, N10665, N10675, N10629, and N10624)3 as shown in Table 1, for use in general corrosive service.

1.2The following products are covered under this specification:

1.2.1Rods 5/16to 3/4in. (7.94 to 19.05 mm) excl in diameter, hot or cold finished, solution annealed and pickled or mechanically descaled.

1.2.2Rods 3/4to 31/2in. (19.05 to 88.9 mm) incl in diameter, hot or cold finished, solution annealed, ground or turned.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM E 8/E8M : 2024 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 8/E8M : 2016 : REV A : EDT 1 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM B 880 : 2014 : R2019 Standard Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
ASTM E 1473 : 2009 Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 8/E8M : 2021 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 1473 : 1994 : REV A : R1998 Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM B 880 : 2024 Standard Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
ASTM E 1473 : 2003 Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 1473 : 2016 : REDLINE Standard Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
ASTM E 1473 : 2022 Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 8/E8M : 2022 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 1473 : 1994 : REV A : R2003 Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
ASTM E 55 : 2023 Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E 8 : 2004 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 1473 : 2016 Standard Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
ASTM E 55 : 2011 : R2017 Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E 55 : 2011 : R2022 : EDT 1 Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.