ASTM B 170 : 2024
Current
The latest, up-to-date edition.
Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes
Hardcopy , PDF
English
01-07-2024
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
B 05
|
| DocumentType |
Standard
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers the requirements for two grades of oxygen-free electrolytic copper wire bars, billets, and cakes produced without the use of metallic or metaloidal deoxidizers.
1.2Oxygen-free copper, as described herein, is defined as copper containing oxygen not in excess of 0.0010 % (10 ppm).
1.2.1Grade 1 copper (UNS C10100) corresponds to the designation OFE in Classification B224.
1.2.2Grade 2 copper (UNS C10200) corresponds to the designation OF in Classification B224.
1.2.3Grade 2 copper may be used to produce OFS designation coppers corresponding to UNS C10400, C10500, and C10700.
1.3Although this specification includes certain UNS designations as described in Practice E527, these designations are for cross reference only and are not specification requirements. In case of conflict, Specification B170 shall govern.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only, except for analytical measurements where SI units are the norm.
1.5The following hazard caveat pertains only to Section 13 and Annex A1 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM B 75/B75M : 2020 | Standard Specification for Seamless Copper Tube |
| ASTM B 251/B251M : 2017 | Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube |
| ASTM B 246 : 2015 : R2021 | Standard Specification for Tinned Hard-Drawn and Medium-Hard-Drawn Copper Wire for Electrical Purposes |
| ASTM F 68 : 2016 | Standard Specification for Oxygen-Free Copper in Wrought Forms for Electron Devices |
| ASTM B 111/B111M : 2024 | Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock |
| ASTM B 152/B152M : 2024 | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
| ASTM B 950 : 2023 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
| ASTM B 447 : 2012 : REV A : R2021 | Standard Specification for Welded Copper Tube |
| ASTM B 1014 : 2020 | Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s) |
| ASTM B 272 : 2012 : R2019 | Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip) |
| ASTM B 187/B187M : 2020 | Standard Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes |
| ASTM B 49 : 2020 | Standard Specification for Copper Rod for Electrical Purposes |
| ASTM B 640 : 2012 : REV A : R2021 | Standard Specification for Welded Copper Tube for Air Conditioning and Refrigeration Service |
| ASTM B 42 : 2020 | Standard Specification for Seamless Copper Pipe, Standard Sizes |
| ASTM B 372 : 2022 | Standard Specification for Seamless Copper and Copper-Alloy Rectangular Waveguide Tube |
| ASTM B 359/B359M : 2023 | Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins |
| SAE AMS4700F:2024 | Copper Wire, Bare, High Purity |
| ASTM B 846 : 2019 : REV A | Standard Terminology for Copper and Copper Alloys |
| ASTM B 846 : 2024 | Standard Terminology for Copper and Copper Alloys |
| ASTM E 50 : 2017 | Standard Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.