ASTM B 160 : 2005 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Nickel Rod and Bar
Hardcopy , PDF
04-03-2021
English
01-05-2005
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.04, 2015 Specifies the nickel (UNS N02200), low carbon nickel (UNS N02201), and solution strengthened nickel (UNS N02211) in the form of hot-worked and cold-worked rod and bar.
| Committee |
B 02
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
1.1 This specification covers nickel (UNS N02200)*, low carbon nickel (UNS N02201)*, and solution strengthened nickel (UNS N02211) in the form of hot-worked and cold-worked rod and bar in the conditions shown in Table 1.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
TABLE 1 Mechanical Properties
| Condition and Diameter or Distance Between Parallel Surfaces, in. (mm) | Tensile Strength, min, psi (MPa) | Yield Strength (0.2 % offset), min. psi (MPa)A | Elongation in 2 in. or 50 mm or 4D, min % |
|---|---|---|---|
| Nickel (UNS N02200) | |||
| Cold-worked (as worked): | |||
| Rounds, 1 (25.4) and under | 80 000 (550) | 60 000 (415) | 10B |
| Rounds over 1 to 4 (25.4 to 101.6) incl. | 75 000 (515) | 50 000 (345) | 15 |
| Squares, hexagons, and rectangles, all sizes | 65 000 (450) | 40 000 (275) | 25B |
| Hot-worked: | |||
| All sections, all sizes | 60 000 (415) | 15 000 (105) | 35C |
| Rings and disksD | — | — | — |
| Annealed: | |||
| Rods and bars, all sizes | 55 000 (380) | 15 000 (105) | 40B |
| Rings and disksE | — | — | — |
| Forging quality | |||
| All sizes | F | F | F |
| Low-Carbon Nickel (UNS N02201) and Solution Strengthened Nickel (UNS N02211) | |||
| Hot-worked: | |||
| All sections, all sizes | 50 000 (345) | 10 000 (70) | 40C |
| Annealed: | |||
| All products, all sizes | 50 000 (345) | 10 000 (70) | 40B |
A See 12.2.
B Not applicable to diameters or cross sections under 3/32 in. (2.4 mm).
C For hot-worked flats 5/16 in. (7.9 mm) and under in thickness the elongation shall be 25%, min.
D Hardness B45 to B80, or equivalent.
E Hardness B45 to B70 or equivalent.
F Forging quality is furnished to chemical requirements and surface inspection only. No tensile properties are required.
| ASTM B 162 : 1999 | Standard Specification for Nickel Plate, Sheet, and Strip |
| ASTM F 85 : 1976 : R2002 | Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes |
| AWS BRH:2007 | BRAZING HANDBOOK |
| ASTM F 85 : 1976 : R2009 | Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes |
| BS EN ISO 4126-2:2003 | Safety devices for protection against excessive pressure Bursting disc safety devices |
| ASTM F 85 : 1976 : R1997 : EDT 1 | Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| DOD-HDBK-249 Revision A:1984 | METALS AND ALLOYS RAPID ON-SITE IDENTIFICATION OF (RECOMMENDED PROCEDURE FOR CHEMICAL SPOT TESTING AND ASSOCIATED PHYSICAL TESTS TO VERIFY METAL ALLOY CLASSIFICATION) (METRIC) |
| AWWA C504 : 2015 | RUBBER-SEATED BUTTERFLY VALVES |
| ASTM F 85 : 1976 : R2018 | Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes (Withdrawn 2023) |
| ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B31.3:2016 | PROCESS PIPING |
| ASTM B 162 : 1999 : R2009 | Standard Specification for Nickel Plate, Sheet, and Strip |
| 15/30299570 DC : 0 | BS ISO 7195 - NUCLEAR ENERGY - PACKAGINGS FOR THE TRANSPORT OF URANIUM HEXAFLUORIDE (UF[6]) |
| AWWA C520 : 2014 | KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM) |
| I.S. EN ISO 4126-2:2003 | SAFETY DEVICES FOR PROTECTION AGAINST EXCESSIVE PRESSURE - PART 2: BURSTING DISC SAFETY DEVICES |
| ASTM F 85 : 1976 : R2013 | Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes |
| ASTM G 134 : 2017 : REDLINE | Standard Test Method for Erosion of Solid Materials by Cavitating Liquid Jet |
| NF ISO 7195 : 2005 | NUCLEAR ENERGY - PACKAGING OF URANIUM HEXAFLUORIDE (UF6) FOR TRANSPORT |
| ISO 7195:2005 | Nuclear energy Packaging of uranium hexafluoride (UF6) for transport |
| CSA C22.2 No. 124 : 2016 | MINERAL-INSULATED CABLE |
| ASTM B 162 : 1999 : R2005 | Standard Specification for Nickel Plate, Sheet, and Strip |
| ISO 4126-2:2003 | Safety devices for protection against excessive pressure Part 2: Bursting disc safety devices |
| UNI EN ISO 4126-2 : 2003 | SAFETY DEVICES FOR PROTECTION AGAINST EXCESSIVE PRESSURE - BURSTING DISC SAFETY DEVICES |
| ASTM B 162 : 1999 : R2014 | Standard Specification for Nickel Plate, Sheet, and Strip |
| ASTM G 32 : 2016 : REDLINE | Standard Test Method for Cavitation Erosion Using Vibratory Apparatus |
| ASME B73.2 : 2016 | Specification for Vertical In-Line Centrifugal Pumps for Chemical Process |
| ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
| ASTM E 1473 : 2016 : REDLINE | Standard Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys |
| ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.