Customer Support: 131 242

i2i Intertek.com
  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
Publishers
ASTM
ASTM A 519/A519M : 2017

ASTM A 519/A519M : 2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing

Available format(s)

Hardcopy , PDF

Superseded date

19-10-2023

Superseded by

ASTM A 519/A519M : 2023

Language(s)

English

Published date

12-06-2017

Publisher

American Society for Testing and Materials

$135.86
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10

This specification covers several grades of carbon and alloy steel seamless mechanical tubing.

Committee
A 01
DocumentType
Standard
Pages
14
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers several grades of carbon and alloy steel seamless mechanical tubing. The grades are listed in Tables 1-3. When welding is used for joining the weldable mechanical tube grades, the welding procedure shall be suitable for the grade, the condition of the components, and the intended service.

TABLE 1 Chemical Requirements of Low-Carbon Steels

Grade Designation

Chemical Composition Limits, %

CarbonA

ManganeseB

Phosphorous,B
max

Sulfur,B
max

MT 1010

0.05–0.15

0.30–0.60

0.040

0.050

MT 1015

0.10–0.20

0.30–0.60

0.040

0.050

MT X 1015

0.10–0.20

0.60–0.90

0.040

0.050

MT 1020

0.15–0.25

0.30–0.60

0.040

0.050

MT X 1020

0.15–0.25

0.70–1.00

0.040

0.050

(A)Limits apply to heat and product analyses.
(B)Limits apply to heat analysis; except as required by 6.1, product analyses are subject to the applicable additional tolerances given in Table 5.

TABLE 2 Chemical Requirements of Other Carbon Steels

Grade Designation

Chemical Composition Limits, %A

Carbon

Manganese

Phosphorous,
max

Sulfur,
max

1008

0.10 max

0.30–0.50

0.040

0.050

1010

0.08–0.13

0.30–0.60

0.040

0.050

1012

0.10–0.15

0.30–0.60

0.040

0.050

1015

0.13–0.18

0.30–0.60

0.040

0.050

1016

0.13–0.18

0.60–0.90

0.040

0.050

1017

0.15–0.20

0.30–0.60

0.040

0.050

1018

0.15–0.20

0.60–0.90

0.040

0.050

1019

0.15–0.20

0.70–1.00

0.040

0.050

1020

0.18–0.23

0.30–0.60

0.040

0.050

1021

0.18–0.23

0.60–0.90

0.040

0.050

1022

0.18–0.23

0.70–1.00

0.040

0.050

1025

0.22–0.28

0.30–0.60

0.040

0.050

1026

0.22–0.28

0.60–0.90

0.040

0.050

1030

0.28–0.34

0.60–0.90

0.040

0.050

1035

0.32–0.38

0.60–0.90

0.040

0.050

1040

0.37–0.44

0.60–0.90

0.040

0.050

1045

0.43–0.50

0.60–0.90

0.040

0.050

1050

0.48–0.55

0.60–0.90

0.040

0.050

1518

0.15–0.21

1.10–1.40

0.040

0.050

1524

0.19–0.25

1.35–1.65

0.040

0.050

1541

0.36–0.44

1.35–1.65

0.040

0.050

(A)The ranges and limits given in this table apply to heat analysis; except as required by 6.1, product analyses are subject to the applicable additional tolerances given in Table 5.

1.2This specification covers both seamless hot-finished mechanical tubing and seamless cold-finished mechanical tubing in sizes up to and including 12 3/4in. [325 mm] outside diameter for round tubes with wall thicknesses as required.

1.3The tubes shall be furnished in the following shapes, as specified by the purchaser: round, square, rectangular, and special sections.

1.4Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order.

1.5The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets or parentheses. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. In this specification hard or rationalized conversions apply to diameter, lengths and tensile properties. Soft conversion applies to other SI measurements.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM A 534 : 2017 : R2022 Standard Specification for Carburizing Steels for Anti-Friction Bearings
ANSI/MSS SP-58:2018 PIPE HANGERS AND SUPPORTS Materials, Design, Manufacture, Selection, Application, and Installation (ANSI-approved American National Standard)

ASTM A 370 : 2021 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1058 : 2014 Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 1040 : 2010 : R2015 : EDT 1 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 1058 : 2012 : REV A Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 1040 : 2007 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 1040 : 2006 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 1058 : 2019 Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 1040 : 2009 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 1040 : 2017 : R2022 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 1058 : 2008 Standard Test Methods for Mechanical Testing of Steel Products<span class='unicode'>—</span>Metric
ASTM A 370 : 2017 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1040 : 2004 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 751 : 2021 Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM A 370 : 2020 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1058 : 2012 Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 1058 : 2012 : REV B Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 370 : 2023 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 751 : 2014 Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
ASTM A 751 : 2020 Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM A 370 : 2011 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1040 : 2010 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
ASTM A 370 : 2022 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1058 : 2009 Standard Test Methods for Mechanical Testing of Steel Products<char: emdash>Metric
ASTM A 1040 : 2017 Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us