ASTM A 134/A134M : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)
Hardcopy , PDF
23-01-2020
English
01-11-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers electric-fusion (arc)-welded straight seam or spiral seam steel pipe NPS 16 and over in diameter (inside or outside as specified by purchaser), with wall thicknesses up to3/4in. [19 mm], inclusive.
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers electric-fusion (arc)-welded straight seam or spiral seam steel pipe NPS 16 and over in diameter (inside or outside as specified by purchaser), with wall thicknesses up to 3/4in. [19 mm], inclusive. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. The pipe is available in various grades based on the ASTM specification ordered (Section 4).
Note 1:Acceptability for many services may be controlled by codes or standards such as those published by the American National Standards Institute and American Society of Mechanical Engineers.
Note 2:For testing methods not specifically covered in this specification, reference can be made to Test Methods and Definitions A370, with particular reference to Annex A2 on Steel Tubular Products.
Note 3:A comprehensive listing of standardized pipe dimensions is contained in ANSI B 36.10.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. In this specification hard or rationalized conversions apply to diameter, lengths, and tensile properties. Soft conversion applies to other SI measurements.
Note 4:The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
1.3The following caveat pertains specifically to Section 5 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 1058 : 2014 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2012 : REV A | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2008 | Standard Test Methods for Mechanical Testing of Steel Products<span class='unicode'>—</span>Metric |
| ASTM A 1058 : 2012 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2012 : REV B | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2009 | Standard Test Methods for Mechanical Testing of Steel Products<char: emdash>Metric |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.