ASTM A 1110/A1110M : 2018
Current
The latest, up-to-date edition.
Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes with 52 KSI [360 MPa] Minimum Yield Strength and Impact Requirements
Hardcopy , PDF
English
21-06-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes where impact properties are required.1.2This tubing is produced in both welded and seamless sizes with a periphery of 88 in. [2235 mm] or less, and a specified wall thickness from 0.148 in. [4 mm] up to 0.875 in. [22 mm].1.3The welded and seamless tubing can be supplied in two different grades each with a specified impact test temperature. Different strength levels, CVN acceptance criteria, and impact test temperatures than listed may be available. To determine their availability, the purchaser should contact the producer (see4.1.4and4.1.13).1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.1.5The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| SupersededBy |
1.1This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes where impact properties are required.
1.2This tubing is produced in both welded and seamless sizes with a periphery of 88 in. [2235 mm] or less, and a specified wall thickness from 0.148 in. [4 mm] up to 0.875 in. [22 mm].
1.3The welded and seamless tubing can be supplied in two different grades each with a specified impact test temperature. Different strength levels, CVN acceptance criteria, and impact test temperatures than listed may be available. To determine their availability, the purchaser should contact the producer (see 4.1.4 and 4.1.13).
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
1.5The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 1058 : 2014 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2012 : REV A | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2008 | Standard Test Methods for Mechanical Testing of Steel Products<span class='unicode'>—</span>Metric |
| ASTM A 1058 : 2012 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2012 : REV B | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 370 : 2011 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2009 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 1058 : 2009 | Standard Test Methods for Mechanical Testing of Steel Products<char: emdash>Metric |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.