ASTM A 1107/A1107M : 2017 : R2022
Current
The latest, up-to-date edition.
Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Steel Drainage Pipes
Hardcopy , PDF
English
09-11-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
A 05
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers the design, material, and minimum performance requirements of resilient connectors used for connections between reinforced concrete structures conforming to Specifications C478 and C913 to corrugated steel drainage pipe conforming to Specifications A760 or A762.
1.1.1These connectors are designed to provide a positive seal between the pipe and manholes or other structures subjected to internal and external hydrostatic pressures less than 10.8 psi [74 KPa].
1.1.2Testing under this standard is limited to hydrostatic pressures. Alternate air and vacuum pressure testing involve unique testing protocols and are not addressed under this standard.
1.1.3Testing under this standard is conducted in a laboratory as a proof of design certification. Actual field performance testing would be accomplished and accepted under individual project performance standards or pipeline acceptance criteria, which is outside the scope of this standard.
Note 1:Infiltration or exfiltration quantities for an installed system are dependent upon many factors other than the connections between manhole structures and pipe, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.
1.2The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see 7.2.4.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 412 : 2024 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM C 913 : 2021 | Standard Specification for Precast Concrete Water and Wastewater Structures |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM C 913 : 2023 | Standard Specification for Precast Concrete Water and Wastewater Structures |
| ASTM F 412 : 2024 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM A 153/A153M : 2016 : REV A | Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware |
| ASTM B 633 : 2019 | Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel |
| ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM B 633 : 2023 | Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel |
| ASTM A 153/A153M : 2023 | Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware |
| ASTM D 746 : 2020 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
| ASTM D 746 : 2024 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.