AS/NZS 5601.1:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Gas installations General installations
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
16-07-2024
23-12-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.Specifies requirements and means of compliance for the design, installation and commissioning of gas installations that are associated with use or intended use of fuel gases such as natural gas, LP Gas, biogas or manufactured gas.
| Committee |
AG-006
|
| DocumentType |
Standard
|
| ISBN |
978 0 7337 9742 2
|
| Pages |
219
|
| PublisherName |
Standards Australia
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
This Standard contains the mandatory requirements and means of compliance for the design, installation and commissioning of gas installations that are associated with the use or intended use of fuel gases such as natural gas, LP Gas, biogas or manufactured gas. The user is expected to be familiar with the properties and characteristics of those fuel gases and the principles of combustion, ventilation and flueing applicable to the safe installation and operation of gas appliances. For New Zealand, these requirements cover gas installations downstream of the point of supply (as defined in the Gas (Safety and Measurement) Regulations 2010.For Australia, these requirements cover gas installations downstream of the outlet of - (a) the consumer billing meter installation; (b) the first regulator on a fixed gas installation where an LP Gas tank or cylinder(s) is installed on site; or (c) the first regulator on site (if no meter is installed) where LP Gas is reticulated from off site storage.Where the term 'installation' is used it is deemed to include the pipework, appliances, flues, air ducts, ventilation and other ancillary items.Section 2 of this Standard contains the performance requirements for the design, installation, and commissioning of gas installations, including those operating at pressures exceeding 200 kPa. It includes, in Clause 2.6.4, some specific limitations as the performance requirements cannot be reliably met if those prohibitions are breeched.Sections 3 to 6 of this Standard contain a means of compliance for installations designed to operate with a gas supply pressure not exceeding 200 kPa. In Australia, approval for any variation to the requirements of Sections 3 to 6 or the normative appendices might need to be obtained from the appropriate Technical Regulator.In New Zealand, the Technical Regulator does not provide approvals for variations to the means of compliance in Sections 3 to 6. References to approval by the Technical Regulator are not applicable to New Zealand. The installation certifier is responsible for ensuring that the installation, including any variations, meets the requirements in Section 2.Where a Standard is cited as part of a means of compliance or in an Appendix, any Standard with equivalent performance requirements may be used as an alternative means of compliance in New Zealand.
Originated in Australia as AS 5601/AG 601-2000.
Previous Australian edition AS 5601-2004.
Originated in New Zealand as NZS 5261:1996.
Previous New Zealand edition NZS 5261:2003.
Jointly revised and redesignated AS/NZS 5601.1:2010.
Reissued incorporating Amendment No. 1 (August 2011).
| AS/NZS 4645.1:2008 | Gas distribution networks Network management |
| AS/NZS 1477:2006 | PVC pipes and fittings for pressure applications |
| AS 3959-2009 | Construction of buildings in bushfire-prone areas |
| AS 2738-2000 | Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings (Reconfirmed 2018) |
| AS 4621-2004 | Regulators for use with liquefied petroleum - Vapour phase |
| AS 4176.1-2010 | Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - General (ISO 21003-1:2008, MOD) (Reconfirmed 2022) |
| AS/NZS 1167.1:2005 | Welding and brazing - Filler metals Filler metal for brazing and braze welding |
| AS/NZS 2648.1:1995 | Underground marking tape Non-detectable tape (Reconfirmed 2020) |
| AS 1572-1998 | Copper and copper alloys - Seamless tubes for engineering purposes (Reconfirmed 2018) |
| AS 4567-2005 | Twin wall metal flues - Gas appliances (Reconfirmed 2017) |
| AS 4176.3-2010 | Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Fittings (ISO 21003-3:2008, MOD) |
| AS 4176.7-2010 | Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Assessment of conformity (ISO/TS 21003-7:2008, MOD) |
| AS/NZS 4645.2:2008 | Gas distribution networks Steel pipe systems |
| AS 1074-1989 | Steel tubes and tubulars for ordinary service (Reconfirmed 2018) |
| AS/NZS 1260:2009 | PVC-U pipes and fittings for drain, waste and vent application |
| AS/NZS 60079.10.1:2009 | Explosive atmospheres Classification of areas - Explosive gas atmospheres (IEC 60079-10-1, Ed.1.0(2008) MOD) |
| AS/NZS 1668.1:1998 | The use of ventilation and airconditioning in buildings Fire and smoke control in multi-compartment buildings |
| AS 4617-2004 | Manual shut off gas valves |
| AS 3688-2005 | Water supply - Metallic fittings and end connectors |
| AS 4623-2008 | Jointing compounds and materials for use in gas pipe joints |
| AS 4627-2005 | Quick-connect devices for gas |
| AS/NZS 3000:2007 | Electrical installations (known as the Australian/New Zealand Wiring Rules) |
| AS 1397-2001 | Steel sheet and strip - Hot-dipped zinc-coated or aluminium/zinc-coated |
| AS/NZS 2208:1996 | Safety glazing materials in buildings |
| AS 4176.2-2010 | Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Pipes (ISO 21003-2:2008, MOD) (Reconfirmed 2022) |
| AS 4176.8-2010 | Multilayer pipes for pressure applications Multilayer pipe systems for consumer gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Specifications for systems (ISO 17484-1:2006, MOD) |
| AS 2944.2-2007 | Plastics pipes and fittings for gas reticulation Polyamide fittings (Reconfirmed 2023) |
| AS 4176.5-2010 | Multilayer pipes for pressure applications Multilayer piping systems for hot and cold water plumbing applications - Fitness for purpose of the system (ISO 21003-5:2008, MOD) (Reconfirmed 2022) |
| AS 4631-2005 | Limited flexibility connectors for gas |
| AS/NZS 4645.3:2008 | Gas distribution networks Plastics pipe systems |
| AS ISO 6993.3-2007 | Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels Fittings and saddles for a maximum operating pressure of 1 bar (100 kPa) |
| AS 4566-2005 | Flue cowls - Gas appliances |
| AS ISO 6993.1-2007 | Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels Pipes for a maximum operating pressure of 1 bar (100 kPa) (ISO 6993-1:2006, MOD) |
| AS 4041-2006 | Pressure piping (Reconfirmed 2016) |
| AS 4553-2008 | Gas space heating appliances |
| AS/NZS 1596:2008 | The storage and handling of LP Gas |
| AS 2030.1-2009 | Gas cylinders General requirements |
| AS 1530.1-1994 | Methods for fire tests on building materials, components and structures Combustibility test for materials (Reconfirmed 2016) |
| AS ISO 7.1-2008 | Pipe threads where pressure-tight joints are made on the threads Dimensions, tolerances and designation |
| AS D26-1972 | Tube fittings with dryseal American standard taper pipe and unified threads for automotive and industrial use (imperial units) (Reconfirmed 2018) |
| AS 2944.1-2007 | Plastics pipes and fittings for gas reticulation Polyamide pipes (Reconfirmed 2023) |
| AS/NZS 1869:1996 | Hose and hose assemblies for liquefied petroleum gases (LP Gas), natural gas and town gas |
| AS/NZS 1530.3:1999 | Methods for fire tests on building materials, components and structures Simultaneous determination of ignitability, flame propagation, heat release and smoke release (Reconfirmed 2016) |
| AS/NZS 4129:2008 | Fittings for polyethylene (PE) pipes for pressure applications |
| AS/NZS 2918:2001 | Domestic solid fuel burning appliances - Installation |
| AS 3673-1989 | Malleable cast iron threaded pipe fittings |
| AS 2700-1996 | Colour Standards for general purposes - Swatches |
| AS 10745-1998 | Information technology - Open Systems Interconnection - Upper layers security model |
| AS 1357.1-2009 | Valves primarily for use in heated water systems Protection valves |
| AS/NZS 4130:2009 | Polyethylene (PE) pipes for pressure applications |
| AS 3814-2009 | Industrial and commercial gas-fired appliances |
| AS/NZS 1734:1997 | Aluminium and aluminium alloys - Flat sheet, coiled sheet and plate (Reconfirmed 2020) |
| AS 1210-2010 | Pressure vessels (Reconfirmed 2021) |
| AS 1345-1995 | Identification of the contents of pipes, conduits and ducts (Reconfirmed 2018) |
| AS 2129-2000 | Flanges for pipes, valves and fittings (Reconfirmed 2016) |
| AS/NZS 1518:2002 | External extruded high-density polyethylene coating system for pipes (Reconfirmed 2016) |
| AS 4629-2005 | Automatic shut off valves and vent valves (Reconfirmed 2018) |
| AS 1432-2004 | Copper tubes for plumbing, gasfitting and drainage applications |
| AS 5262-2011 | LP Gas mobile industrial direct fired air heaters |
| AS/NZS 5601.2:2010 | |
| AS 4558-2011 | Decorative gas log and other fuel effect appliances |
| AS 4556-2011 | Indirect gas-fired ducted air heaters |
| AS 1668.4-2012 | The use of ventilation and airconditioning in buildings Natural ventilation of buildings |
| AS/NZS 5601.2:2013 | Gas installations LP Gas installations in caravans and boats for non-propulsive purposes |
| AS 5263.0-2013 | Gas appliances General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.