AS/NZS 4058:2007
Current
The latest, up-to-date edition.
Precast concrete pipes (pressure and non-pressure)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
18-04-2007
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Proposes minimum requirements for the materials to be used in, and the manufacture of, controlled quality precast concrete pipes, and proposes methods of sampling, testing and classifying concrete pipes manufactured in accordance with this Standard. It applies to circular precast pipes, manufactured from concrete, unreinforced or with circumferential steel reinforcement, that are intended for pressure or non pressure water supply, drainage, waste water or sewerage applications or service ducts.
| Committee |
WS-006
|
| DocumentType |
Standard
|
| ISBN |
0 7337 8161 6
|
| Pages |
54
|
| ProductNote |
Pending Revision indicates that as a result of the Aged Standards review process, the document needs updating. If no project proposal, meeting the quality criteria, is received within the 12 month timeframe, the document shall be withdrawn.
|
| PublisherName |
Standards Australia
|
| Status |
Current
|
| Supersedes |
This Standard describes minimum requirements for materials and manufacture of controlled quality precast concrete pipes. It also describes minimum requirements for sampling, testing and classifying concrete pipes manufactured in accordance with this Standard.This Standard applies to circular precast pipes manufactured from concrete, unreinforced or with circumferential steel reinforcement, that are intended for pressure or non-pressure water supply, drainage, sewerage or service duct applications.This Standard does not apply to the following:Cast in situ pipes, box culverts, or structural members covered by other Australian Standards.Precast prestressed concrete pipe, embedded steel cylinder pipe, and fibre-reinforced concrete pipe or precast concrete cylindrical access chamber components, or pipes made of other materials.Requirements for fittings fabricated from pipes complying with this Standard are not specified in this Standard.Requirements for ordering and supplying concrete pipes are given in Section 6 (see Note 2).This Standard does not cover the assessment of external service loads to which a pipe will be subjected in particular installation conditions. Therefore, purchasers should specify pipe design characteristics and routine testing requirements that are appropriate to the intended embedment and service conditions. Where a purchaser is not the concrete pipe asset owner, the purchaser should consult with the asset owners designer or specifier to determine these requirements, prior to ordering. AS/NZS 3725 should be referred to for the selection, design and specification of buried concrete pipe installations.
Originated, in part, as AS A35-1957 and AS A124-1962.
AS A35 revised and designated AS 1342-1973, AS A124 revised and designated AS 1392-1974.
AS 1342-1973 and AS 1392-1974 revised and designated AS 4058-1992.
AS 4058-1992 and NZS 3107:1978 jointly revised and designated AS/NZS 4058:2007.
| AS 1726-1993 | Geotechnical site investigations |
| AS 1379-1997 | Specification and supply of concrete |
| AS/NZS 3725:2007 | Design for installation of buried concrete pipes |
| AS 2758.1-1998 | Aggregates and rock for engineering purposes - Concrete aggregates |
| AS 1646.1-2000 | Elastomeric seals for waterworks purposes - General requirements |
| AS 3610 Supp1-1995 | Formwork for concrete - Blowhole and colour evaluation charts (Supplement to |
| AS/NZS 4671:2001 | Steel reinforcing materials |
| AS 1379 SUPP 1-1997 | Specification and supply of concrete - Commentary (Supplement to AS 1379-1997) |
| AS 3610-1995 | Formwork for concrete |
| AS 3610 SUPP 2-1996 | Formwork for concrete - Commentary (Supplement to AS 3610-1995) |
| AS 3582.2-2001 | Supplementary cementitious materials for use with portland and blended cement Slag - Ground granulated iron blast-furnace |
| AS 1646.3-2000 | Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds |
| AS/NZS 3582.3:2002 | Supplementary cementitious materials for use with portland and blended cement Amorphous silica |
| AS 3582.1-1998 | Supplementary cementitious materials for use with portland and blended cement Fly ash |
| AS 1646.2-2000 | Elastomeric seals for waterworks purposes Material requirements for pipe joint seals used in water and wastewater applications - Specifies by prescription formulation |
| AS 3972-1997 | Portland and blended cements |
| AS 1478.1-2000 | Chemical admixtures for concrete, mortar and grout Admixtures for concrete (Reconfirmed 2018) |
| AS 1379-2007 | Specification and supply of concrete (Reconfirmed 2017) |
| AS 3735-2001 | Concrete structures for retaining liquids |
| AS 4139-2003 | Fibre-reinforced concrete pipes and fittings (Reconfirmed 2018) |
| AS 1646-2007 | Elastomeric seals for waterworks purposes (Reconfirmed 2018) |
| AS/NZS 7000:2016 | Overhead line design |
| AS 1735.3-2002 | Lifts, escalators and moving walks Passenger and goods lifts - Electrohydraulic |
| AS/NZS 3500.5:2012 | Plumbing and drainage Housing installations |
| AS/NZS 3725:2007 | Design for installation of buried concrete pipes |
| AS/NZS 3500.3:2003 | Plumbing and drainage Stormwater drainage |
| AS 5100.8:2017 | Bridge design Rehabilitation and strengthening of existing bridges |
| AS/NZS 3500.3:2018 | Plumbing and drainage Stormwater drainage |
| AS/NZS 7000:2010 | Overhead line design - Detailed procedures |
| AS/NZS 4327:1995 | Metal-banded flexible couplings for low-pressure applications (Reconfirmed 2020) |
| AS 5100.3:2017 | Bridge design Foundation and soil-supporting structures |
| AS 1735.1-2003 | Lifts, escalators and moving walks General requirements |
| AS/NZS 3500.3:2015 | Plumbing and drainage Stormwater drainage |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.