16/30319470 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 16611 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITHOUT PRESSURE - NON-CIRCULAR PIPES AND JOINTS MADE OF GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESINS (UP) - DIMENSIONS, REQUIREMENTS AND TESTS
Hardcopy , PDF
30-06-2017
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions and Symbols
4 General requirements
5 Pipes
6 Fittings
7 Joint performance
Annex A (informative) - Recommendation of the
calculation process
Bibliography
BS ISO 16611.
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
35
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 7685:1998 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness |
| ISO 10467:2004 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 10928:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use |
| CEN/TR 15729:2010 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Report on the determination of mean abrasion after a defined number of test cycles |
| ISO 8639:2016 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| CEN/TS 14632:2012 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 8533:2003 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints |
| ISO 2078:1993 | Textile glass Yarns Designation |
| ISO 8513:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength |
| ISO 10468:2003 | Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor |
| ISO 10952:2014 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 4633:2015 | Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.