12/30261215 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 13060 - SMALL STEAM STERILIZERS
Hardcopy , PDF
31-12-2014
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General technical requirements
5 Performance requirements
6 Safety, risk control and usability
7 Categories of tests
8 Test equipment
9 Test programme
10 Test methods
Annex A (informative) - Clarification of the definition
of narrow lumens and simple hollow items
Annex B (informative) - Process evaluation system
Annex C (informative) - Suggested maximum limits
of contaminants in and specification for
water for steam sterilization
Annex D (informative) - Example of a table to be
supplied with pre-purchase documentation and
with the instructions for use
Annex E (informative) - Load support systems
Annex F (informative) - Rationale for the tests
Annex G (informative)
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 93/42 EEC
on medical devices
Bibliography
BS EN 13060
| Committee |
LBI/35
|
| DocumentType |
Draft
|
| Pages |
80
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 13060 : DRAFT 2012 | Identical |
| EN ISO 14937:2009 | Sterilization of health care products - General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices (ISO 14937:2009) |
| ISO 11607-2:2006 | Packaging for terminally sterilized medical devices Part 2: Validation requirements for forming, sealing and assembly processes |
| EN 61010-2-040:2015 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-040 Particular requirements for sterilizers and washer-disinfectors used to treat medical materials |
| ISO 11138-3:2017 | Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization processes |
| ISO 4126-1:2013 | Safety devices for protection against excessive pressure — Part 1: Safety valves |
| EN 60584-2:1993 | Thermocouples - Part 2: Tolerances |
| EN 285:2015 | Sterilization - Steam sterilizers - Large sterilizers |
| IEC 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
| EN 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
| EN 868-5:2009 | Packaging for terminally sterilized medical devices - Part 5: Sealable pouches and reels of porous materials and plastic film construction - Requirements and test methods |
| EN 868-4:2017 | Packaging for terminally sterilized medical devices - Part 4: Paper bags - Requirements and test methods |
| EN 764-1:2015+A1:2016 | Pressure equipment - Part 1: Vocabulary |
| EN ISO 11138-3:2017 | Sterilization of health care products - Biological indicators - Part 3: Biological indicators for moist heat sterilization processes (ISO 11138-3:2017) |
| ISO 13485:2016 | Medical devices Quality management systems Requirements for regulatory purposes |
| ISO 14937:2009 | Sterilization of health care products General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO 4017:2014 | Fasteners Hexagon head screws Product grades A and B |
| EN 867-5:2001 | Non-biological systems for use in sterilizers - Part 5: Specification for indicator systems and process challenge devices for use in performance testing for small sterilizers Type B and Type S |
| EN 868-6:2017 | Packaging for terminally sterilized medical devices - Part 6: Paper for low temperature sterilization processes - Requirements and test methods |
| EN 868-2:2017 | Packaging for terminally sterilized medical devices - Part 2: Sterilization wrap - Requirements and test methods |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO/IEC Guide 99:2007 | International vocabulary of metrology Basic and general concepts and associated terms (VIM) |
| EN 61326-1:2013 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements |
| EN 868-3:2017 | Packaging for terminally sterilized medical devices - Part 3: Paper for use in the manufacture of paper bags (specified in EN 868-4) and in the manufacture of pouches and reels (specified in EN 868-5) - Requirements and test methods |
| EN ISO 11140-1:2014 | Sterilization of health care products - Chemical indicators - Part 1: General requirements (ISO 11140-1:2014) |
| ISO 11140-1:2014 | Sterilization of health care products Chemical indicators Part 1: General requirements |
| EN 1041:2008+A1:2013 | Information supplied by the manufacturer of medical devices |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 60751:2008 | INDUSTRIAL PLATINUM RESISTANCE THERMOMETERS AND PLATINUM TEMPERATURE SENSORS |
| ISO/TS 11139:2006 | Sterilization of health care products Vocabulary |
| IEC 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| EN ISO 4017:2014 | Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2014) |
| EN ISO 14971:2012 | Medical devices - Application of risk management to medical devices (ISO 14971:2007, Corrected version 2007-10-01) |
| EN 61010-1:2010 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| EN ISO 17665-1:2006 | Sterilization of health care products - Moist heat - Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 17665-1:2006) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 11607-1:2006 | Packaging for terminally sterilized medical devices Part 1: Requirements for materials, sterile barrier systems and packaging systems |
| EN 868-7:2017 | Packaging for terminally sterilized medical devices - Part 7: Adhesive coated paper for low temperature sterilization processes - Requirements and test methods |
| ISO 17664:2017 | Processing of health care products Information to be provided by the medical device manufacturer for the processing of medical devices |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.