12/30259203 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 12007-5 - GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES, SPECIFIC FUNCTIONAL REQUIREMENTS
Hardcopy , PDF
31-07-2014
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Design
5 Construction
6 Quality control
7 Pressure testing
8 Commissioning and decommissioning
9 Operation and maintenance
Annex A (normative) - Jointing methods
Bibliography
BS EN 12007-5
| Committee |
GSE/33
|
| DocumentType |
Draft
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 12007-5 : DRAFT 2012 | Identical |
| EN 12327:2012 | Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| PREN 12007-3 : DRAFT 2013 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 3: SPECIFIC FUNCTIONAL REQUIREMENTS FOR STEEL |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 1515-1:1999 | Flanges and their joints - Bolting - Part 1: Selection of bolting |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 12007-1:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| EN 751-2:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds |
| EN 15266:2007 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| EN 10241:2000 | Steel threaded pipe fittings |
| CEN/TR 13737-1:2012 | Implementation Guide for functional standards prepared by CEN/TC 234 Gas infrastructure - Part 1: General |
| EN 751-1:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| EN 12007-4:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation |
| EN 14291:2004 | Foam producing solutions for leak detection on gas installations |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| EN 1776:2015 | Gas infrastructure - Gas measuring systems - Functional requirements |
| EN 12186:2014 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.