12/30245656 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ISO/DIS 3951-2 - SAMPLING PROCEDURES FOR INSPECTION BY VARIABLES - PART 2: GENERAL SPECIFICATION FOR SINGLE SAMPLING PLANS INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION OF INDEPENDENT QUALITY CHARACTERISTICS
Hardcopy , PDF
30-09-2013
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Acceptance quality limit (AQL)
6 Switching rules for normal, tightened and
reduced inspection
7 Relationship to ISO 2859-1 and ISO 3951-1
8 Consumer protection
9 Accommodating measurement variability
10 Planning
11 Choice between variables and attributes
12 Choice between the s-method and [sigma] - method
13 Choice of inspection level and AQL
14 Choice of sampling scheme
15 Preliminary operations
16 Standard univariate s-method procedures
17 Standard multivariate s-method procedures for
independent quality characteristics
18 Standard univariate [sigma] - method procedures
19 Standard multivariate [sigma] - method procedures
for independent quality characteristics
20 Standard multivariate combined s-method and
[sigma] - method procedures for independent
quality characteristics
21 Procedure during continuing inspection
22 Normality and outliers
23 Records
24 Operation of switching rules
25 Discontinuation and resumption of inspection
26 Switching between the s-method and
[sigma] - method
Annex A (normative) - Table for determining the
sample size code letter
Annex B (normative) - Form k s-method single
sampling plans
Annex C (normative) - Form k "[sigma]" method
single sampling plans
Annex D (normative) - Form p* s-method single
sampling plans
Annex E (normative) - Form p* [sigma] - method
single sampling plans
Annex F (normative) - Values of f[s] for maximum
sample standard deviation (MSSD)
Annex G (normative) - Values of f[[sigma]] for
maximum process standard deviation (MPSD)
Annex H (normative) - Estimating the process fraction
nonconforming for sample size 3: s-method
Annex I (normative) - Values of for upper control limit
on the sample standard deviation
Annex J (normative) - Supplementary acceptability
constants for qualifying towards reduced
inspection
Annex K (normative) - Procedures for obtaining
s and [sigma]
Annex L (normative) - Estimating the process fraction
nonconforming
Annex M (informative) - Consumer's risk qualities
Annex N (informative) - Producer's risks
Annex O (informative) - Operating characteristics for
the [sigma] - method
Annex P (informative) - Accommodating measurement
variability
Bibliography
ISO/DIS 3951-2
| Committee |
SS/5
|
| DocumentType |
Draft
|
| Pages |
106
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| ISO 16269-4:2010 | Statistical interpretation of data Part 4: Detection and treatment of outliers |
| ISO 7870:1993 | Control charts General guide and introduction |
| ISO 31-11:1992 | Quantities and units Part 11: Mathematical signs and symbols for use in the physical sciences and technology |
| ISO 10576-1:2003 | Statistical methods — Guidelines for the evaluation of conformity with specified requirements — Part 1: General principles |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| MIL-STD-414 Base Document:1957 | SAMPLING PROCEDURE AND TABLE FOR INSPECTION BY VARIABLES FOR PERCENT DEFECTIVE |
| ISO 16269-6:2014 | Statistical interpretation of data — Part 6: Determination of statistical tolerance intervals |
| ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
| ISO 2859-10:2006 | Sampling procedures for inspection by attributes Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 3534-1:2006 | Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.