09/30152273 DC : 0
Current
The latest, up-to-date edition.
BS IEC/TS 60034-20-2 - ROTATING ELECTRICAL MACHINES - PART 20-2: PERFORMANCE CHARACTERISTICS AND TESTING SPECIFICATIONS FOR BRUSHLESS PERMANENT MAGNET MOTORS
Hardcopy , PDF
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 Scope
2 Normative references
3 Terms and definitions
3.1 Brushless Permanent Magnet motor (BPM)
3.2 Environment/Temperature
3.3 Motor shaft/torque-speed/power ratings
3.4 Motor winding & voltage ratings
3.5 Power dissipation
3.6 Mechanical
4 Characteristic ratings of BPM motor
4.1 Torque-speed & output shaft data
4.2 Deleted
4.3 Power loss dissipation
4.4 Mechanical
4.5 Options
4.6 Rating plate
5 Interface of BPM motor to converter
5.1 Torque ratings
5.2 Voltage at motor terminals
5.3 Common mode voltage
6 Testing
6.1 Motor type (design verification) testing for
catalogue data
6.2 Routine (Production) testing
6.3 Installation testing of motor
Annex A - Published data
A.1 Motor manufacturer published data
A.2 Drive module data required for BPM
A.3 Application data required for sizing BPM
Annex B - Control block diagrams
B.1 Motor control block diagram for K[t]
B.2 Equivalent control block diagram for K[e]
B.3 Equivalent control block diagram for drive, motor,
load and servo
B.4 Shaft voltage equivalent circuit
Annex C - Thermal management
C.1 Power loss dissipation
C.2 Winding time constants
Annex D - Feedback devices comparison
Annex E - Sizing a BPM motor
Annex F - Method for evaluating torque ripple of PDS
BS IEC/TS 60034-20-2
| Committee |
PEL/2
|
| DocumentType |
Draft
|
| Pages |
61
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| IEC 60034-9:2003+AMD1:2007 CSV | Rotating electrical machines - Part 9: Noise limits |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC TS 60034-27:2006 | Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines |
| ISO 1940-1:2003 | Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| IEC 60072-1:1991 | Dimensions and output series for rotating electrical machines - Part 1: Frame numbers 56 to 400 and flange numbers 55 to 1080 |
| IEC TS 60034-18-41:2006 | Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters |
| IEC 60034-18-22:2000 | Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions |
| ISO 8821:1989 | Mechanical vibration Balancing Shaft and fitment key convention |
| IEC 60034-18-1:2010 | Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines |
| IEC 60034-8:2007+AMD1:2014 CSV | Rotating electrical machines - Part 8: Terminal markings anddirection of rotation |
| IEC TS 60034-25:2014 | Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide |
| IEC 60034-14:2003+AMD1:2007 CSV | Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity |
| IEC 60034-18-21:2012 | Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| IEC 60034-2:1972 | Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles) |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.