UNI EN ISO 12215-6 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 6: STRUCTURAL ARRANGEMENTS AND DETAILS
11-15-2018
01-01-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 General
6 Structural arrangement
6.1 Stiffening
6.2 Hull girder strength
6.3 Load transfer
6.4 Determination of stiffener spans
6.5 Window mullions
6.6 Sailboat mast support
7 Specific structural details for FRP construction
7.1 Local reinforcement
7.2 Bonding
7.3 Major joints
7.4 Laminate transition
7.5 Sandwich construction
7.6 Attachment of fittings
7.7 Engine seatings and girders
7.8 Hull drainage
8 Specific structural details for metal construction
8.1 Design details
8.2 End connections
8.3 Increased hull plating
8.4 Protective keel
8.5 Hull drainage
8.6 Machinery spaces
8.7 Good practice welding standards
8.8 Good practice for riveting or adhesive bonding
9 Good practice on laminated wood
9.1 Edge sealing
9.2 Plywood orientation
9.3 Local scantlings
9.4 Alternative criteria
10 Consideration of other loads
11 Other structural components
11.1 General
11.2 Rudder structure and connection
11.3 Keel attachment
11.4 Introduction and distribution of rigging loads
11.5 Other structural components not considered in
other parts
Annex A (normative) - Structural arrangements for
category C and D boats
Annex B (informative) - Determination of shear stresses
within a stiffener with glued or riveted joints
Annex C (informative) - Good practice welding procedure
Annex D (informative) - Longitudinal strength analysis
Annex ZA (informative) - Relationship between this
International Standard and the Essential
Requirements of EU Directive 94/25/EC
Bibliography
Describes structural details and structural components not explicitly included in ISO 12215-5, ISO 12215-7, ISO 12215-8 and ISO 12215-9. Applicable to monohull and multihull small craft constructed from fibre reinforced plastics (FRP), aluminium or steel alloys, wood or other suitable boat building material, with a hull length, in accordance with ISO 8666, of up to 24 m.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 12215-6:2008 | Identical |
| ISO 12215-6:2008 | Identical |
| ISO 12215-5:2008 | Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
| ISO 9692-4:2003 | Welding and allied processes — Recommendations for joint preparation — Part 4: Clad steels |
| ISO 6520-1:2007 | Welding and allied processes Classification of geometric imperfections in metallic materials Part 1: Fusion welding |
| ISO 13920:1996 | Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position |
| ISO 10042:2005 | Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections |
| ISO 8666:2016 | Small craft Principal data |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| ISO 9692-3:2016 | Welding and allied processes Types of joint preparation Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys |
| ISO 6520-2:2013 | Welding and allied processes — Classification of geometric imperfections in metallic materials — Part 2: Welding with pressure |
| ISO 9692-2:1998 | Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| ISO 12216:2002 | Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.