UNI 11466 : 2012
Current
The latest, up-to-date edition.
HEAT PUMP GEOTHERMAL SYSTEMS - DESIGN AND SIZING REQUIREMENTS
11-27-2012
INTRODUZIONE
1 SCOPO E CAMPO DI APPLICAZIONE
2 RIFERIMENTI NORMATIVI
3 TERMINI E DEFINIZIONI
4 REQUISITI DI PROGETTAZIONE
APPENDICE A (normativa) - DIMENSIONAMENTO DEGLI
SCAMBIATORI DI CALORE A TERRENO A
SVILUPPO VERTICALE - METODO DI CALCOLO
ANALITICO PER IL DIMENSIONAMENTO
APPENDICE B (normativa) - DIMENSIONAMENTO DEGLI SCAMBIATORI
DI CALORE A TERRENO A SVILUPPO ORIZZONTALE -
METODO DI CALCOLO ANALITICO PER IL DIMENSIONAMENTO
APPENDICE C (informativa) - COMBINAZIONE DI TENSIONI DOVUTI
ALLA PRESENZA DI CARICO STRUTTURALE E CARICO
TERMICO AL TERRENO NEL CASO DI PALI ENERGETICI
APPENDICE D (normativa) - DETERMINAZIONE DELLA TEMPERATURA
MEDIA DEL FLUIDO TERMOVETTORE LATO TERRENO -
PER GLI SCAMBIATORI DI CALORE A TERRENO A
SVILUPPO VERTICALE
APPENDICE E (normativa) - ESTENSIONE DEL CAMPO TERMICO IN
PRESENZA DI ACQUA DI FALDA
APPENDICE F (normativa) - METODO CARRIER PER IL CALCOLO
DELLA POTENZA FRIGORIFERA DI UN EDIFICIO
APPENDICE G (normativa) - METODO MENSILE PER IL CALCOLO
DELL'ENERGIA FRIGORIFERA LATENTE DI UN EDIFICIO
APPENDICE H (informativa) - ESEMPI NUMERICI
APPENDICE I (normativa) - TEST DI RISPOSTA TERMICA (TRT)
APPENDICE J (informativa) - ESEMPIO DI TEST DI RISPOSTA TERMICA
DEL TERRENO (TRT)
APPENDICE K (normativa) - TUBAZIONI IN PLASTICA
BIBLIOGRAFIA
This standard sets design and sizing criteria and calculus procedures for the determination of both design and peridic performances of heat pump geothermal systems This standrds allows to determine the contribution of renewable energies provided by geothermal heat pump for the energeic certification of buildings.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Current
|
| UNI 11467 : 2012 | HEAT PUMP GEOTHERMAL SYSTEMS - INSTALLATION REQUIREMENTS |
| UNI/TS 11487 : 2013 | HEAT PUMP GEOTHERMAL SYSTEMS - INSTALLATION REQUIREMENTS FOR DIRECT EXPANSION SYSTEMS |
| UNI 11517 : 2013 | HEAT PUMP GEOTHERMAL SYSTEMS - REQUIREMENTS FOR QUALIFICATION OF INSTALLING FIRMS PROVIDING GEOTHERMAL EXCHANGER |
| UNI 11468 : 2012 | HEAT PUMP GEOTHERMAL SYSTEMS - ENVIRONMENTAL REQUIREMENTS |
| UNI/TS 11300-3 : 2010 | ENERGY PERFORMANCE OF BUILDINGS - PART 3: EVALUATION OF PRIMARY ENERGY AND SYSTEM EFFICIENCIES FOR SPACE COOLING |
| UNI 11467 : 2012 | HEAT PUMP GEOTHERMAL SYSTEMS - INSTALLATION REQUIREMENTS |
| UNI EN 12201-3 : 2013 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS |
| UNI/TS 11300-4 : 2012 | ENERGY PERFORMANCE OF BUILDINGS - PART 4: RENEWABLE ENERGY AND OTHER GENERATION SYSTEMS FOR SPACE HEATING AND DOMESTIC HOT WATER PRODUCTION |
| UNI EN 12201-2 : 2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| UNI EN ISO 1167-2 : 2006 | THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 2: PREPARATION OF PIPE TEST PIECES |
| UNI EN 15603 : 2008 | ENERGY PERFORMANCE OF BUILDINGS - OVERALL ENERGY USE AND DEFINITION OF ENERGY RATINGS |
| UNI EN 12828 : 2014 | HEATING SYSTEMS IN BUILDINGS - DESIGN FOR WATER-BASED HEATING SYSTEMS |
| UNI EN 15316-4-2 : 2008 | ENERGY PERFORMANCE OF BUILDINGS - METHOD FOR CALCULATION OF SYSTEM ENERGY REQUIREMENTS AND SYSTEM EFFICIENCIES - PART 4-2: SPACE HEATING GENERATION SYSTEMS, HEAT PUMP SYSTEMS, MODULE M3-8-2, M8-8-2 |
| UNI EN 12831 : 2006 | HEATING SYSTEMS IN BUILDINGS - METHOD FOR CALCULATION OF THE DESIGN HEAT LOAD |
| UNI TS 11300-1 : 2014 | ENERGY PERFORMANCE OF BUILDINGS - PART 1: EVALUATION OF ENERGY NEED FOR SPACE HEATING AND COOLING |
| UNI EN 15450 : 2008 | HEATING SYSTEMS IN BUILDINGS - DESIGN OF HEAT PUMP HEATING SYSTEMS |
| UNI TS 11300-2 : 2014 | ENERGY PERFORMANCE OF BUILDINGS - PART 2: EVALUATION OF PRIMARY ENERGY NEED AND OF SYSTEM EFFICIENCIES FOR SPACE HEATING, DOMESTIC HOT WATER PRODUCTION, VENTILATION AND LIGHTING FOR NON-RESIDENTIAL BUILDINGS |
| UNI EN 378-3 : 2012 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 3: INSTALLATION SITE AND PERSONAL PROTECTION |
| UNI EN 378-1 : 2012 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 1: BASIC REQUIREMENTS, DEFINITIONS, CLASSIFICATION AND SELECTION CRITERIA |
| UNI EN ISO 15875-1 : 2008 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 1: GENERAL |
| UNI EN 14336 : 2004 | HEATING SYSTEMS IN BUILDINGS - INSTALLATION AND COMMISSIONING OF WATER BASED HEATING SYSTEMS |
| UNI 11468 : 2012 | HEAT PUMP GEOTHERMAL SYSTEMS - ENVIRONMENTAL REQUIREMENTS |
| UNI EN 378-2 : 2012 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 2: DESIGN, CONSTRUCTION, TESTING, MARKING AND DOCUMENTATION |
| UNI EN 14825 : 2013 | AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS, WITH ELECTRICALLY DRIVEN COMPRESSORS, FOR SPACE HEATING AND COOLING - TESTING AND RATING AT PART LOAD CONDITIONS AND CALCULATION OF SEASONAL PERFORMANCE |
| UNI EN ISO 15875-2 : 2008 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES |
| UNI EN 378-4 : 2012 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 4: OPERATION, MAINTENANCE, REPAIR AND RECOVERY |
| UNI EN ISO 15494 : 2005 | PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE), POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT), CROSSLINKED POLYETHYLENE (PE-X), POLYPROPYLENE (PP) - METRIC SERIES FOR SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM |
| UNI EN 15265 : 2008 | ENERGY PERFORMANCE OF BUILDINGS - CALCULATION OF ENERGY NEEDS FOR SPACE HEATING AND COOLING USING DYNAMIC METHODS - GENERAL CRITERIA AND VALIDATION PROCEDURES |
| UNI EN 12309-2 : 2002 | GAS-FIRED SORPTION APPLIANCES FOR HEATING AND/OR COOLING WITH A NET HEAT INPUT NOT EXCEEDING 70 KW - PART 2: SAFETY |
| UNI 10672 : 1997 | MAJOR HAZARD PROCESS PLANTS - SAFETY ASSURANCE PROCEDURES FOR DESIGN |
| UNI EN ISO 1167-1 : 2006 | THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 1: GENERAL METHOD |
| UNI 10349 : 1994 | HEATING AND COOLING OF BUILDING - CLIMATIC DATA |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.