UL 60950-22:2ED 2017-03-31
Current
The latest, up-to-date edition.
Information Technology Equipment - Safety - Part 22: Equipment to be Installed Outdoors
Hardcopy
03-31-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
PREFACE
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Conditions for outdoor equipment
5 Marking and instructions
6 Protection from electrical shock in an outdoor location
7 Wiring terminals for connection of external conductors
8 Construction requirements for outdoor enclosures
9 Protection of equipment within an outdoor enclosure
10 Mechanical strength of enclosures
11 Outdoor equipment containing valve regulated or
vented batteries
Annex A (normative) - Water-saturated sulphur dioxide
atmosphere
Annex B (normative) - Water spray test
Annex C (normative) - Ultraviolet light conditioning test
Annex D (normative) - Gasket tests
Annex E (informative) - Rationale
Annex NAE (informative) - U.S. and Canadian regulatory
Bibliography
This new edition of ANSI/UL 60950-22 is being issued to update requirements to those published in IEC 60950-22, second edition.
| DevelopmentNote |
Jointly published by CSA and UL. Also numbered as CSA C22.2.60950.22. (04/2017) NEW CHILD REV 1 2022 IS NOW ADDED.
|
| DocumentType |
Standard
|
| Pages |
0
|
| ProductNote |
NEW CHILD REV 1 2022 IS NOW ADDED.
|
| PublisherName |
Underwriters Laboratories
|
| Status |
Current
|
This part of IEC 60950 applies to information technology equipment intended to be installed in an OUTDOOR LOCATION.
| CSA C22.2 No. 62368-1 : 2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| NFPA 731 : 2017 | INSTALLATION OF ELECTRONIC PREMISES SECURITY SYSTEMS |
| CSA C22.2 No. 94.1 : 2015 | ENCLOSURES FOR ELECTRICAL EQUIPMENT, NON-ENVIRONMENTAL CONSIDERATIONS |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| IEC 60364-4-43:2008 | Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent |
| UL 50:13ED 2015-10-16 | Enclosures for Electrical Equipment, Non-Environmental Considerations |
| NFPA 780 : 2017 | INSTALLATION OF LIGHTNING PROTECTION SYSTEMS |
| IEC 61587-1:2016 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation |
| IEC 60896-21:2004 | Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test |
| IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV | Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| CSA C22.2 No. 144 : 1991 | GROUND FAULT CIRCUIT INTERRUPTERS |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| UL 943:5ED 2016-05-17 | Ground-Fault Circuit-Interrupters |
| ISO 14993:2001 | Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 21207:2015 | Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| IEEE C2-2017 | NATIONAL ELECTRICAL SAFETY CODE (NESC)(R) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60896-22:2004 | Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements |
| ISO/TS 18173:2005 | Non-destructive testing General terms and definitions |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| CSA C22.2 No. 62368-1 : 2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| IEC 61643-11:2011 | Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods |
| IEC 61969-3:2011 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| IEC 61439-5:2014 | Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 62485-2:2010 | Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries |
| CSA C22.2 No. 94.2 : 2015 | ENCLOSURES FOR ELECTRICAL EQUIPMENT, ENVIRONMENTAL CONSIDERATIONS |
| ISO 3231:1993 | Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.