PREN 14364 : DRAFT 2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
Superseded date
02-01-2013
Superseded by
Published date
01-12-2013
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions and symbols
4 General requirements
5 Pipes
6 Fittings
7 Joint performance
Annex A (normative) - Test method for the resistance to
bending and pressure of end-thrust loaded
joints in pipe systems
Bibliography
Describes the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage with or without pressure.
| Committee |
TC 155
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 11/30246458 DC : 0 | Identical |
| 04/30118849 DC : DRAFT SEP 2004 | EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE SYSTEMS BURIED IN GROUND |
| 03/102154 DC : DRAFT MAY 2003 | CEN TS 14632 - PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| 05/30127634 DC : DRAFT JAN 2005 | PREN 13566-7 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NONPRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY WOUND UNPLASTICIZED POLY (VINYLE CHLORIDE) (PVC-U) PIPES |
| I.S. CEN TS 14578:2003 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY OR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GPR) BASED ON UNSATURATED POLYESTER RESIN (UP) - RECOMMENDED PRACTICE FOR INSTALLATION |
| BS EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with cured-in-place pipes |
| DD CEN/TS 14578:2003 | Plastics piping systems for water supply or drainage and sewerage. Glass-reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP). Recommended practice for installation |
| 04/30118843 DC : DRAFT SEP 2004 | EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE |
| I.S. EN 13566-4:2003 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| I.S. CEN TS 14807:2004 | PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES |
| EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes |
| ISO 8521:2009 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO 7432:2002 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| ISO 7685:1998 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| ISO/TR 10465-3:2007 | Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits |
| ISO 10928:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| CEN/TS 14632:2012 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| ISO 527-5:2009 | Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites |
| EN 1447:2009+A1:2010 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| EN 476:2011 | General requirements for components used in drains and sewers |
| ISO 8533:2003 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints |
| ISO 2078:1993 | Textile glass Yarns Designation |
| ISO 8483:2003 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints |
| ISO 8513:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength |
| ISO 10468:2003 | Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor |
| ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
| ISO 10466:1997 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring deflection |
| ISO 10471:2003 | Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions |
| EN ISO 527-5:2009 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009) |
| EN 1119:2009 | Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements |
| ISO 10952:2014 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
| ISO 2531:2009 | Ductile iron pipes, fittings, accessories and their joints for water applications |
| EN 1452-3 : 1999 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 3: FITTINGS |
| CEN/TS 14578:2013 | Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.